Color imagination SI-051 User Manual Download Page 5

Page: 5 / 6

7. Control

Control

Control Modes

Modes

A. Auto Mode

For this mode, the users can select color and zoom macro for desired effect.

1. Press MODE and select "Auto".

2. Press ENTER to access "Color" or "Zoom".

3. Use UP/DOWN to select desired effect.

B. Sound Mode

For this mode, the zoom par runs to the beat of music.

1. Press MODE and select "Sound".

2. Press ENTER to access sound programs.

3. Use UP/DOWN to select sound programs.

4. Press ENTER and use UP/DOWN to set sound sensitivity level.

C. Manual Mode

For this mode, the users can manually adjust zoom and each color of red, green, blue.

Press MODE and select "Zoom".

Press ENTER to access color or zoom.

Use UP/DOWN to adjust parameter of color or zoom.

D. DMX Mode

For this mode, the zoom par functions on 9 DMX channels.

1. Press MODE and select :DMX".

2. Press ENTER to access DMX address.

3. Use UP/DOWN to set the start address of the par.

4. Mounting

Mounting

Mounting and

and

and Installation

Installation

Cautions:

For added protection mount the fixtures in areas outside walking paths, seating areas,

or in areas were the fixture might be reached by unauthorized personnel.

Before mounting the fixture to any surface, make sure that the installation area can hold a

minimum point load of 10 times the device’s weight.

Fixture installation must always be secured with a secondary safety attachment, such as an

appropriate safety cable.

Never stand directly below the device when mounting, removing, or servicing the fixture.

from a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture is kept at

least 0.5m (1.5 ft) away from any flammable materials (decoration etc.).

Always use and install the supplied safety cable as a safety measure to prevent accidental damage

and/or injury in the event the clamp fails.

Mounting

Mounting points

points

points::::

Overhead mounting requires extensive experience, including amongst others

calculating working load limits, a fine knowledge of the installation material being used, and

periodic safety inspection of all installation material and the fixture. If you lack these qualifications,

do not attempt the installation yourself. Improper installation can result in bodily injury.

Be sure to complete all rigging and installation procedures before connecting the main power

cord to the appropriate wall outlet.

Mounting

Mounting::::

The LED Zoom Par provides a unique mounting bracket assembly. Please use the

qualified light hook hanging it to the truss or use the screws to fix it to the ceiling or any

application areas. Then add a safety chain to the lights to ensure the safety of handing.

Summary of Contents for SI-051







Search results

Summary of Contents for SI-051

Reviews:

Brands by name

Popular brands

Color imagination SI-051, User Manual

Search results

Summary of Contents for SI-051

Reviews:

Brands by name

Popular brands