manualshive.com logo in svg

Colop digital e-mark create, Operating And Maintenance Manual, Page: 46 / 60

Share
Download
Colop digital e-mark create Operating And Maintenance Manual Download Page 46

 

 

   

e-mark create marking device

 

Chapter 6 Maintenance 

CODI Standard 1.0

 

 

46/60 

Operating and Maintenance Manual 

 

 

 

Fig. 38: Charge battery 

4. 

Connect the charger to the mains power supply. 

 

DANGER!

 

Risk of a fatal electric shock in wet conditions. 

Never handle the charger mains plug with wet hands. Never use the device in humid 
areas. Never expose the battery and charger, including USB port, to water and/or rain. 

 

 

 

The e-mark create can be charged when switched on or off. Charging starts whenever it is placed in the 

docking station. 

 

5. 

Observe charge indicator lights (charging cable is connected) on the Light Guide (

see chapter 5.3

): 

-

 

yellow flashing next to the charging plug forwards continuously: Charge indicator light, battery charge 

between 0% and 49%, battery charging  

-

 

green flashing next to the charging plug forwards continuously: Charge indicator light, battery charge 

between 50% and 99%, battery charging  

-

 

continuous green light next to the charging plug: Battery is fully charged (100 %). Charging stops 

automatically and the charger can be removed. 

 

The light guide also shows the battery level when not charging (

see chapter 5.3

): 

-

 

Red flashing around the e-mark create indicates low battery charge (below 10 %) 

-

 

Continuous yellow light next to charging socket indicates low battery level (between 10 and 24 %) 

-

 

Continuous green light next to charging socket indicates sufficient/high battery level (between 25 and 

100 %) 

 

 

Summary of Contents for digital e-mark create





























































Reviews:

No comments