Coleman FlowClear 90402E, Owner'S Manual

Page: 7 / 10

NOTE:
It is important to ensure all elements: Hoses, Debris Screens and Inlet/Outlet Valves are properly aligned.
Operation
1) Open/unscrew the Air Purge Valve on the top of the Filter Pump; air is released as water fills the Filter Pump.
Note:
If knob should become dislodged, simply place it back into the hole and turn clockwise to rethread air purge valve.
2) When water comes out of the Air Purge Valve screw it closed and wipe away any water.
3) Test the GFCI plug.
NOTE:
It is imperative to check that the hydraulic connectors are not closed.
PEDESTAL FIXING
The filter pump must be vertically fixed on ground or a certain pedestal made of wood or concrete before use. There
should be two holes 9mm in diameter on the pedestal, the space between which should be 166mm. Put filter pump on the
pedestal and fix them together by fasten the bolts and nuts. All the pedestal parts should weigh over 18kgs at least to
prevent the pump from accidentally falling.
390 166
390
250
166
2-M8 bolt
2-M8 nut
B
A
A
B
B
A
A
B
A. To test the GFCI plug, insert it into a grounding type receptacle.
B. Press the “RESET” button; the indicator turns red.
GFCI Test
RESET
TEST
RESET
TEST
RESET
TEST
A B C D
7
NOTE:
If the indicator light is not on, the test has failed.
C. Press the “TEST” button. The indicator turns off.
NOTE:
If the indicator light is not off, the test has failed.
D. Press the “RESET” button, the indicator light turns red, and the filter pump is ready for use.
WARNING:
RISK OF ELECTRIC SHOCK. THE GFCI MUST BE TESTED BEFORE EACH USE.
WARNING:
DO NOT USE THE PUMP IF THE ABOVE TEST FAILS.
Please contact your local Bestway Customer Service.
NOTE:
To prevent the risk of electrical shock, ensure your hands are completely dry when plugging-in the Filter
Pump.
IMPORTANT:
DO NOT DRY RUN THE FILTER PUMP - Make sure both the pool’s Inlet and Outlet valves
are fully covered by water before operating the Filter Pump.
Maintenance
CAUTION:
YOU MUST ENSURE THE FILTER PUMP IS UNPLUGGED BEFORE ANY MAINTENANCE OR
STORAGE BEGIN S OR SEVERE RISK OF INJURY OR DEATH EXISTS.
1) Unplug the Filter Pump.
2) Loosen the Hose Clamps on the pool’s Inlet and Outlet Hoses by unscrewing the fly nut counter-clockwise.
3) Remove Debris Screens from the inside of the pool.
4) Replace the Debris Screens with the Stopper Plugs in the pool’s Inlet and Outlet Valves.
5) Unscrew the Filter Cap Retainer and remove the Filter Cap.
6) Clean the Filter Cartridge with a garden hose, if filter cartridge remains soiled or discolored, it is necessary to replace it with a
new one.
7) Insert the cleaned (or new) Filter Cartridge; ensure it is centered in the Filter Pump.
8) Check that the Filter Cap Seal is in place.
9) Replace the Filter Cap and screw the Filter Cap Retainer into position.
10) Replace the Stopper Plugs with the Debris Screens in the pool’s Inlet and Outlet Valves. Tighten the Hose Clamps.
Water will now flow to the pump.
11) Follow the PUMP INSTALLATION DIRECTIONS section to prepare the system for use.
IMPORTANT:
For sanitary reasons we suggest replacing the Filter Cartridge with a new one every two
weeks.
STORAGE
1) Unplug the Filter Pump.
2) Follow the instructions as previously outlined to stop water flowing to the Filter Pump and to remove the Filter Cartridge.
3) Discard the Filter Cartridge.
4) Detach all Hoses.
5) Dry all components thoroughly.
6) Store the filter pump in a dry location out of the reach of children. Storage temperature: 4-40 O C ( 39.2-104 O F )
Pump Warranty
For information concerning pump warranty please visit our website at: www.bestwaycorp.com