background image

THROTTLE  ADJUSTMENT

10

Performing maintenance and 

checks while the engine is running 

could be hazardous.
You could be severely injured by 

moving parts or hot surfaces.
Never perform maintenance or 

check procedures while the engine 

is running with the exception of 

checking the engine stop switch or 

throttle. 

!

WARNING

Failing to inspect and maintain the 

Mini Bike could be hazardous.  
Not following the pre-ride

inspection procedures could result 

in loosing control of the Mini Bike 

resulting in an accident or damage 

to the Mini Bike
Always perform a Pre-ride inspec-

tion before each ride.

PRE-RIDE INSPECTION

!

WARNING

Inspecting and checking the 

condition of the Mini Bike before 

each ride is important.  Following 

the pre-ride check list will help 

insure there are no problems which 

could result in injury or becoming 

stranded.   Make sure the Mini 

Bike is in good operating condition 

before each ride.  

WHAT TO 

CHECK

CHECK FOR

Steering

•  Smoothness

•  No restriction of     

movement

Brakes

•   Proper brake lever 

play

Tires

•  Proper tire pressure

Fuel Tank •  Enough fuel for the ride

•  Fuel cap secure

•  Hoses have no signs of 

cracks or leaks

Throttle 

grip

•  Throttle grip snaps 

back to idle when 

released

•  Operates freely

•  Has correct free play

Engine 

Stop 

Switch

•  Switch shuts off engine 

when activated.  

Engine 

Oil

•  Correct oil level

Drive 

Chain

•  Proper tension

•  Lubricated

General 

Condition

or frame while running

• 

  Axle nuts tight

•  All  nuts and bolts tight

•  No rattles from engine 

Summary of Contents for CT100U














Reviews:

Related manuals for CT100U