background image

Introduction

Thank you for purchasing this piece of Stuart 
equipment. To get the best performance from 
the equipment and for your own safety, please 
read these instructions carefully before use. 
Before discarding the packaging check that all 
parts are present and correct.

This equipment is designed to operate under the 
following conditions:

❖ 

For indoor use only

❖ 

Use in a well ventilated area

❖ 

Ambient temperature range +5ºC to +40ºC

❖ 

Altitude to 2000m

❖ 

Relative humidity not exceeding 80%

❖ 

Mains supply fluctuation not exceeding 10%

❖ 

Over-voltage category II IEC60364-4-443

❖ 

Pollution degree 2

If the equipment is not used in the manner 
described in this manual and with accessories 
other than those recommended by Stuart, the 
protection provided may be impaired.

Electrical Installation

          THIS EQUIPMENT MUST BE EARTHED

Before connection please ensure that the 
line supply corresponds to that shown on 
the rating plate. 

Model 

Supply requirements 

Power

SI60 

220-240V, 50Hz 

350W

Si60D 

220-240V, 50Hz 

350W

All models are supplied with two mains leads 
fitted with IEC plugs for connection to the 
instrument. One has a U.K. 3 pin plug and the 
other has a 2 pin “Schuko” plug for connection 
to the mains. Choose the lead appropriate for 
your electrical installation and discard the other. 
Should neither lead be suitable, take the lead 
with the U.K. plug and replace the plug with a 
suitable alternative. This involves cutting off the 
moulded plug, preparing the cable and 
connecting to the re-wireable plug in accordance 
with its instructions.

THIS OPERATION SHOULD ONLY BE 
UNDERTAKEN BY A QUALIFIED ELECTRICIAN

NOTE:

 Refer to the equipment’s rating plate to 

ensure that the plug and fusing are suitable for 
the voltage and wattage stated.

The wires in the mains cable are coloured as 
follows:
BROWN 

- LIVE

BLUE  

- NEUTRAL

GREEN/YELLOW - EARTH

The instruments are fitted with an IEC socket at 
the rear of the instrument for connection of the 
mains lead. The appropriate mains lead should 
be connected BEFORE connection to the mains 
supply. 

Should the mains lead need replacement, a cable 
of 1mm

2

 

of harmonised code H05W-F connected 

to an IEC320 plug should be used. 

IF IN DOUBT CONSULT A QUALIFIED 
ELECTRICIAN

Safety Advice Before Use

❖ 

The unit should be carried with both hands, 
with fingers under each side of the frame.

❖ 

Never move or carry the unit while it is in use 
or connected to the mains supply.

  Do not mix flammable liquids or use the

 

equipment in hazardous atmospheres.

  In case of mains interruption, a fault or

 

mechanical failure, the unit will continue to

 

operate on removal of fault.

  Mechanical energy can lead to breakage of

 

glass vessels. Use with care.

  Do not position the unit such that it is

 

difficult to disconnect it from the mains by

 

removing the mains cable from the socket at

 

the back.

USE CAUTION WHEN REMOVING 

VESSELS FROM THE INCUBATOR AS 
PARTS MAY BE HOT.

Summary of Contents for Stuart SI60









Reviews: