background image

Cole-Parmer Instrument Company 

Manufactured by:

 Barnant Company

 

 

Page 

2 of 24

 

INTRODUCTION............................................................................................................. 3 

SAFETY CONSIDERATIONS ......................................................................................... 4 

FUNCTIONAL DESCRIPTION........................................................................................ 5 

THEORY OF OPERATION ............................................................................................. 6 

TROUBLESHOOTING .................................................................................................. 15 

REPAIR PROCEDURES............................................................................................... 18 

REPLACEMENT PARTS LISTING................................................................................ 21 

CALIBRATION ............................................................................................................. 22 
 
FUNCTIONAL TESTS................................................................................................... 23 
 
ASSOCIATED DOCUMENTS ....................................................................................... 25 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

INTRODUCTION

 

 

 

 

Service for this product is performed at three levels: the customer, 

distributor/COLE-PARMER and factory/depot repair.  This manual describes dis-
tributor/COLE-PARMER service procedures. 

 
Barnant Company

 

y

 28W092 Commercial Avenue 

y

 Barrington, IL  U.S.A.  60010-2392 

847-381-7050 

y

 800-637-3739 

y

 847-381-7053 (Fax)  

e-mail: 

[email protected]

 

y

 Web Site:  http//www.barnant.com 

 

 

Summary of Contents for 75211-30

























Reviews: