Coemar ReLite Led Kit T / D Manual Download Page 10 | Manualshive

Page: 10 / 25

background image

Italiano

10

6

. Control signal connections

Warning!

Make sure that screening and conductors are not in contact one another or with the

metal housing of the connector.

Pin#1 and housing must never be connected to the power supply unit.

6.1

Control signal connection by XLR5 plugs

The digital control signal is transmitted to the projector via a two pole cable screened in according to the Inter-

national standards for DMX 512 data transmission. The connection must be serial, using connectors XLR5 male

and female located on the back of

ReLite Led Kit

labelled DMX512 IN e OUT.

DMX In

DMX Out

«
...
8
9
10
11
12
...
»

Summary of Contents for ReLite Led Kit T / D


























Reviews:

No comments

Related manuals for ReLite Led Kit T / D

Brand: GE Pages: 698

Brand: Panasonic Pages: 180

Brand: Datalogic Pages: 48

Brand: PageFlip Pages: 32

Brand: IBS Scherer Pages: 64

Brand: Octane Fitness Pages: 20

Brand: Oceaneering Pages: 27

Brand: Radial Engineering Pages: 16

Brand: R&S Pages: 61

APT-9411 Series

Brand: TAKAYA Pages: 77

Brand: Tadano Pages: 402

Brand: Valcom Pages: 6

Brand: Vaisala Pages: 60

ULTRATHERM 908i

Brand: gbo Pages: 32

Brand: Dantel Pages: 6

Brand: Zero 88 Pages: 22

Brand: Yaasa Pages: 20

Brand: ubicquia Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands