12.4. Electronic motor alignment
The display panel of the
miniCYC MB
allows for the electronic alignment of the projector’s motors in the optical system. This procedure
is performed by
Coemar
at the factory. It may be useful to perform this procedure in the case of internal components being replaced
(motors, electronic parts, sensor, ecc.).
Altering the factory settings may radically alter the functioning of the projector. Carefully read all of the following prior to attempting any
changes.
Electronic calibration
1.
Press the
menu
button and then
enter
to confirm.
2.
Press the
+
or
-
button until
FUNC
is displayed. Then press
enter.
3.
Press the
+
or
-
button until
RESE
is displayed.
4.
Press the
enter
and menu buttons simultaneously, holding them for at least
10"
. The motors will perform a reset and the display will
show
-- -- -- --
for a few seconds. After this, the display will show
ALIG
confirming that you have entered electronic calibration mode.
Note:
Simultaneously pressing the
+
and
-
buttons will return the calibration value to 128 (default).
Press together
enter
and
menu
keys for
10 seconds: the display will show this menu
☞
menu
☞
+
o
–
FUNC
AOO1
ALIG
alignment
Motors alignment
END
end
To end the procedure and to record it
☞
enter
A 0 0 1
☞
+
o
–
LEFT
Left lamp hour meter reset
To reset the lamp hour meter of the left lamp.
The operation must made every lamp change.
☞
enter
C.LAM
lamp hour reset
To reset the lamp hour meter
☞
enter
☞
+
o
–
☞
+
o
–
SURE
confirm reset
SURE
confirm reset
RIGH
Right lamp hour meter reset
To reset
the lamp hour meter of the left lamp.
The operation must made every lamp change.
☞
+
o
–
☞
enter
☞
enter
☞
+
o
–
PAN
pan alignment
pan movement alignment
☞
enter
0 1 2 8
☞
enter
☞
+
o
–
es.
0 1 2 0
☞
enter
0 1 2 8
☞
enter
☞
+
o
–
es.
0 1 2 0
☞
enter
0 1 2 8
☞
enter
☞
+
o
–
es.
0 1 2 0
☞
enter
0 1 2 8
☞
enter
☞
+
o
–
es.
0 1 2 5
☞
enter
0128
☞
enter
☞
+
o
–
es.
0 1 2 7
☞
enter
0128
☞
enter
☞
+
o
–
es.
0 1 2 7
☞
enter
0128
☞
enter
☞
+
o
–
es.
0 1 2 7
☞
+
o
–
☞
+
o
–
☞
+
o
–
☞
+
o
–
☞
+
o
–
☞
+
o
–
☞
+
o
–
TILT
tilt alignment
tilt movement alignment
DIMM
dimmer alignment
Alignment of dimmer
ZOOM
zoom alignment
alignment of zoom
CYAN
cyan alignment
cyan filter alignment
MAGE
magenta alignment
magenta filter alignment
YELL
yellow alignment
yellow filter alignment
MIC.M
ulpoad main
Ulpoad main software
☞
enter
UPLD
upload
Software upload from DR1
☞
enter
☞
+
o
–
☞
+
o
–
SURE
confirm
ulpoad
SURE
confirm
ulpoad
MIC.D
upload display
Upload display software
☞
+
o
–
☞
enter
☞
enter
☞
enter
MIC.M
download main
Download main software
☞
enter
DULD
download
Download software to DR1
☞
enter
☞
+
o
–
☞
+
o
–
SURE
confirm
download
SURE
confirm
download
MIC.D
download display
Download display software
☞
+
o
–
☞
enter
☞
enter
☞
enter
☞
enter
☞
enter
RESE
ATTENTION!!
The alignment procedure can only be carried out when DMX 512 signal is connected.
ATTENTION!!
This procedure should only be undertaken by qualified and experienced technical personnel..
23
English