28
English
14. Error Messages
If you have to check a malfunction,
Infinity Spot L
has an auto diagnostic system that visualizes in the lower part of
the display one or more intermittent messages, preceded by “ERR”.
The following table will help you to understand these messages correctly. If the problem persists despite carrying out
the suggested procedure, contact your
Coemar Customer Service Centre
.
Error Messages
Description and suggested solution
ERR: Memory FAILURE
Internal memory writing error. Contact your authorized Coemar Service center
ERR: CFG data FAILURE
Configuration data error. The initial parameter setting has failed, the projector has loaded its factory default setting.
Turn the projector off and on again. Should the error reoccur, refer to your authorised Coemar service centre
ERR: DMX address
DMX addressing error. The projector is not receiving all DMX channels needed to operate correctly. Check the DMX
address indicated on the display and the number of channels being output from the controller (some controllers do
not exceed 12 channels)
ERR: DMX frame
DMX frame error. DMX signal present but frame too short; the controller has not enough channels to control the
projector
ERR: No Slave LINK
Communication error. The LCD board is not communicating properly with the main board. Check the cabling
connecting the boards or refer to your authorised Coemar service centre.
ERR: No Ballast LINK
Communication error. The LCD board is not communicating properly with the ballast. Check the cabling
connecting the boards or refer to your authorised Coemar service centre.
ERR: Ballast Temp. #1
Primary ballast temperature too high. Check that the ambient temperature does not exceed 40°C check also the
proper functioning of the fans.
ERR: Ballast Temp.#2
Secondary ballast temperature too high. Check that the ambient temperature does not exceed 40°C check also the
proper functioning of the fans.
ERR: Vin line low
Too low main power input. Main power voltage is too low, it must be at least 90 Vac.
ERR: Vout lamp high
Too high lamp voltage. Lamp can be exhausted and so consume more power than normal. Replace the lamp and if
needed, refer to your authorised Coemar service centre.
ERR: Encoder PAN
PAN encoder not found. Check the sensor on the encoder wheel placed at the base to detect the position of the
PAN movement motor; check the motor and the relevant cabling
ERR: Encoder TILT
TILT encoder not found. Check the sensor of the encoder wheel placed on the fixture’s yoke to detect the position
of the TILT movement motor; check the motor and the relevant cabling
ERR: Sensors Line #2
The sensor does not detect the magnet. Check sensor and motor cabling of the Gobos assembly.
ERR: Sensors Line #3
Sensor line 3 error. Control circuit error relating to position sensors for the motors. (EFFECTS, ZOOM, FOCUS) posta
nella forcella: il sensore non rileva il magnete. The sensor does not detect the magnet. Check sensor and motor
cabling of the Zoom, Focus and effect wheel.
ERR: Sensors Line #5
Sensor line 5 error. Control circuit error relating to position sensors for the motors of the colour changer assembly.
The sensor does not detect the magnet. Check sensor and motor cabling of the colour changer assembly.
ERR: EFFECT Wheel
Position error of the effect wheel. The sensor does not detect the magnet. Check the functioning and the correct
positioning of the magnetic sensor of the effect wheel.
ERR: EFFECT Index
Initial position error of the effect. The sensor does not detect the magnet. Check the functioning and the correct
positioning of the magnetic sensor placed on effect #1.
ERR: COLOR Wheel
Position error of the color wheel. The sensor does not detect the magnet. Check the functioning and the correct
positioning of the magnetic sensor of the colour wheel. Check the correct tightening of the transmission belt.
ERR: GOBO 1 Wheel
Position error of the gobo wheel 1. The sensor does not detect the magnet. Check the functioning and the correct
positioning of the magnetic sensor of the gobos 1 wheel.
ERR: GOBO 1 Index
Initial position error of the gobo wheel 1. The sensor does not detect the magnet. Check the functioning and the
correct positioning of the magnetic sensor placed on gobos 1.
ERR: GOBO 2 Wheel
Position error of the gobo wheel 2. The sensor does not detect the magnet. Check the functioning and the correct
positioning of the magnetic sensor of the gobos 2 wheel.
ERR: ZOOM
Zoom error. The sensor does not detect the magnet. Check the functioning and the correct positioning of the
magnetic sensor placed on the Zoom lens carriage. Check the correct tightening of the transmission belt.
ERR: FOCUS
Focus error. The sensor does not detect the magnet. Check the functioning and the correct positioning of the
magnetic sensor placed on the Focus lens carriage. Check the correct tightening of the transmission belt.
