background image

 

15 

Code Corporation, 434 Ascension Way, Ste. 300, Murray, Utah 84123 

 

www.codecorp.com

 

Statement of Agency Compliance 

 

NOTE: This equipment has been tested and found to comply with the limits for 
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and 
on, the user is encouraged to try to correct the interference by one or more of 
the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from  

 

that to which the receiver is connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

 

Industry Canada (IC) 

 

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is 
subject to the following two conditions: (1) this device may not cause interference, and (2) this 
device must accept any interference, including interference that may cause undesired operation 
of the device. 

 

Industrie Canada (IC) 

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio 
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne 
doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage 
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. 

 

 

 

Summary of Contents for CR7000 Series

















Reviews: