Code Blue CB 4 Series Administrator'S Manual Download Page 50

Page: 50 / 65

Code Blue

•

259 Hedcor Street

•

Holland, MI 49423 USA

•

800.205.7186

•

www.codeblue.com

GU-160-T

page 50 of 65

CB 4 Series

Administrator Guide

33 Cellular Retro Instructions (CB 4-u only)

TELULAR SX-5E & CALLFINDER CX100FX2 GSM-4 TO GSM-5

Installation Instructions

Retrofit Instructions Telular & CallFinder

We strongly advise reading these instructions before any work is started. In addition, the actual wir-

ing may have changed by others, therefore the wiring guides provided are originals and here for your

reference.

Some early 2002 designs: a total rebuild is more effective and easier to accomplish. Contact Customer
Service a rebuild kit.

Telular GSM Removal Instructions Specifically

If you still have a Telular cellular F.C.T. (Fixed Cellular Terminal), inside your CB 1

NightCharge

or CB 1-w (Solar), CB 4-u NightCharge

or CB 4-u Solar enclosure,

it is a hardwired internal harness. The wiring in the enclosure is bundled, therefore

removing two wires from the bundled group is very time consuming. You may choose

to reuse existing wiring, or cutting and splicing the power wires is acceptable. If doing

so, use self-sealing splices.

Consideration: abandoning the original power wires will require you to identify the

harness and power panel in order to properly attach the new GSM-5 power wires.

Review the list below for the most common configurations.

Hint: Cellular power terminates on the same buss as the battery.

Models involved in this Retro – Visual Refer document Attached

CB1

CB 4-u

NightCharge

2002, 2005, 2010

NightCharge

2002, 2005, 2010

Solar 2005, 2008, 2010 - 13

Summary of Contents for CB 4 Series


































































Search results

Summary of Contents for CB 4 Series

Reviews:

Related manuals for CB 4 Series

Brands by name

Popular brands

Code Blue CB 4 Series, Administrator'S Manual

Search results

Summary of Contents for CB 4 Series

Reviews:

Related manuals for CB 4 Series

Brands by name

Popular brands