Code Alarm PC 4400 Owner'S Manual Download Page 4

4

* Throughout this manual, ‘press’ refers to pressing

for less than 1 second; ‘press and hold’ refers to
pressing for more than 1 second.

** ’Siren’ also refers to the vehicle horn if it is used as the alarm sounding device.*

If you have chosen the Silent Arming Option, the siren will not sound when arming or disarming until the
appropriate button is pressed a second time.

Press for Car Finder

Press and Hold for
Panic Alarm

Press and Hold for
Auxilary 2

Arming the Security System

To arm the system, exit the vehicle, close all doors, then press* the
ARM button. The siren** will “chirp” twice

 and the parking lights will

flash twice, indicating the system is armed. The doors will also lock at
this time (if equipped and connected). The status indicator (red
warning light on the dash) will blink steadily, once per second.

Pre-arm Mode

If the siren chirps and the parking lights flash only once, this indicates
that the vehicle courtesy light is on, or that an entrance is not closed
securely. Check to see that doors, hood, and trunk are properly
closed. Once all entrances are secured (and the courtesy light is off),
the system will chirp / flash again. The system is now fully armed.
(If the entrance is not secured within 4 minutes, the system will arm
and ignore the unsecured entrance until it is closed.)

Disarming the Security System

To disarm the system, press the DISARM button. The siren will chirp
and the parking lights will flash once, and the doors will unlock. The
courtesy light will turn on for 1 minute, or until the vehicle is started.

Attempted Intrusion Identification

If the siren chirps four times when disarming, this indicates that the
system was triggered in your absence. The status indicator will also
flash rapidly. Perform the following operation to determine the protected
zone that triggered the system:

After disarming, press the
emergency override button.
The siren will chirp to indicate
the cause of the alarm trigger:

1 chirp IT-s Interior Theft Sensor

2 chirps Door

3 chirps Hood

4 chirps Trunk/Optional Sensors

5 chirps Ignition was turned on

Using Your  Remote Transmitter

Press for two-car
operation (SHIFT)

Press and hold to activate
auxilary 4

Press to DISARM Security
System and Unlock Doors

Press TWICE for Two-Stage
Door Unlock*

Press and Hold to Open Trunk

Press to ARM,the
security system

Press and hold to
activate Auxilary 1

Press and hold to
actiavate auxilary 3

Summary of Contents for PC 4400
















Reviews: