background image

8

Using Your Remote Starter 

(cont’d)

setting off the alarm setting off the alarm.

Remote Start Safety Features

For safety and security reasons, the Code Alarm CA-640

TM

  will shut

off the vehicle during remote start if any of the following occur:

• The vehicle hood is opened
• The brake is pressed before the vehicle ignition is turned ON

with the key

• The engine reaches 3 times its normal idle
• The alarm is triggered

As a safety precaution, the vehicle will shut off if left unattended for 12
or 24 minutes, depending on the time preset by your installer.

Entering the Vehicle While It is Running via Remote Start

1. Press UNLOCK to unlock the door(s) and turn off the alarm

system (if it is not already off).

2. Enter the vehicle. Do not press the brake pedal.
3. Insert the key into the ignition and turn to the ON position.
4. Press the brake pedal. The remote starter disengages and the

vehicle will operate normally.

Pre-Heating or Pre-Cooling the Interior of the Vehicle

Before exiting the vehicle, set the temperature controls to the desired
setting and operation. After the CA-640

TM

 starts the vehicle, the heater

or air-conditioning will activate and heat or cool the interior to your
setting.

Turning on the Rear-Window Defroster (if connected)

While the vehicle is running via remote start, the vehicle defroster will
automatically activate and run for 10 minutes, or for your vehicle’s
preset time limit.

Using the “Quick-stop” Feature

If you want to make a short stop and leave your vehicle running (to keep
the interior warm or cool, for instance), the quick stop feature allows
you to do this while keeping your vehicle secure and your keys with you.

To engage quick stop:

1. Stop the vehicle and place the transmission in PARK.
2. With your foot off the brake pedal, press the START button on
the remote control for 2 seconds. The parking lights will turn on,
indicating that the vehicle is now running via remote start.
3. Remove the keys from the ignition and exit the vehicle. Press

LOCK/ARM to arm the alarm system if desired.

Note:

 Do not leave children or animals unattended in the vehicle

when using the quick stop feature.

ca-640 owners.pmd

9/9/2004, 4:19 PM

8

Summary of Contents for CA-640





















Reviews: