Code Alarm Ca 1053 Owner'S Manual Download Page 3

3

2012 Audiovox Electronics Corporation. All rights reserved.

 Arming the Security System    

 

To arm the system, exit the vehicle, close all doors, then press the 

 button. The 

parking lights will flash 2 times, indicating the system is armed, has locked the doors 

(if equipped and connected) and activated the starter disable feature. The LED status 

indicator will blink steadily, once per second.  

  NOTE: The system is equipped with a feature called Silent Choice. If enabled, the 

system requires a second press of the 

 button to activate an audible arming 

response from the vehicle.

 Passive Arming Bypass

 

If passive arming is enabled on your system, while the system is disarmed, press  

  

2 times within 5 seconds, the system will respond with 1 chirp and the LED will turn 

on. The security system will remain in this temporally bypassed state for as long as 

you wish. To exit passive bypass, press the 

 or   button and the system will return 

to normal status.

 Bypassing The Shock Sensor 

 

To arm the system and ignore the shock sensor press 

  button, then within 5 

seconds press 

  + 

 , the system will respond with 1 long chirp.

 

NOTE:

 The system will only change the shock sensor setting for one arm cycle and 

will be defaulted back to normal operation the next time the system is armed. 

 

 Hidden Alarm Function

 

Press the 

  button first, within 3 seconds press the 

 button to activate the hidden 

alarm function. The security system will arm with “Hidden Alarm Function” in which the 

siren / horn will be silenced if the system is triggered.

 Disarming the Security System

 

To disarm the system press the 

 button. The parking lights will flash 1 time, 

indicating the system is disarmed and has unlocked the doors (if equipped and 

connected).

  NOTE: The system is equipped with a feature called Silent Choice. If enabled, the 

system requires a second press of the   button to activate an audible disarming 

response from the vehicle.

 *Throughout this manual, ‘press’ refers to pressing for less than 1 second; ‘press and hold’ refers to pressing for more 

than 2 seconds.

  Using Your Remote Control

Summary of Contents for Ca 1053











Reviews: