Code 3 ROCKERPAK430 Installation & Operation Manual Download Page 8

RockerPak is a trademark of Code 3, Inc.  Code 3 is a registered trademark of  Code 3, Inc. a subsidiary of Public Safety Equipment, Inc.

Code 3, Inc.

10986 N. Warson Road

St. Louis, Missouri 63114-2029—USA

www.code3pse.com

WARRANTY

This product was tested and found to be operational at the time of manufacture. Provided this

product is installed and operated in accordance with the manufacturer's recommendations, Code 3, Inc.
guarantees all parts and components except the lamps for a period of 1 year from the date of purchase
or delivery, whichever is later. Units demonstrated to be defective within the warranty period will be
repaired or replaced at the factory service center at no cost.

Use of a lamp or other electrical load of a wattage higher than installed or recommended by the

factory, or use of inappropriate or inadequate wiring or circuit protection causes this warranty to be-
come void. Failure or destruction of the product resulting from abuse or unusual use and/or accidents is
not covered by this warranty.

Code 3, Inc. shall in no way be liable for other damages including consequential, indirect or

special damages whether loss is due to negligence or breach of warranty.

CODE 3, INC. MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY INCLUDING, WITH-

OUT LIMITATION, WARRANTIES OF FITNESS OR MERCHANTABILITY, WITH RESPECT TO
THIS PRODUCT.

PRODUCT RETURNS

If a product must be returned for repair or replacement*, please contact our factory to obtain a

Return Goods Authorization Number  (RGA number) before you ship the product to Code 3, Inc.  Write
the RGA number clearly on the package near the mailing label.  Be sure you use sufficient packing
materials to avoid damage to the product being returned while in transit.

*Code 3, Inc. reserves the right to repair or replace at its discretion.  Code 3, Inc. assumes no responsibility or liability for expenses incurred for the

removal and /or reinstallation of products requiring service and/or repair.; nor for the packaging, handling, and shipping: nor for the handling of products return to
sender after the service has been rendered.

Revision 4, 02/2006 - Instruction Book Part No. T04922

©2001-6 Code 3, Inc.      Printed in USA

NEED HELP?  Call our Technical Assistance Hotline - (314) 996-2800

Summary of Contents for ROCKERPAK430









Reviews: