Coda Amplifier 10.5 Operation Manual Download Page 15

 14

WARRANTY

I. Warranty- Any failure of the Amplifier 10.5 to operate or to meet specifications,
applicable at time of manufacture, due to a manufacturing defect or component
failure, will be corrected by Coda Technologies, Inc. without charge for parts, or labor
for a period of 

ten years

 from date of original purchase.  Coda Technologies, Inc.  will

provide for surface transportation to and from the factory from an authorized Coda
Technologies, Inc. dealer for a period of one year from date of purchase.

II. Procedure- 

If the Amplifier 10.5 should require service under warranty,  take it with proof

of purchase date, with its carton and packing material, to a Coda Technologies, Inc.
dealer.

  The dealer will arrange for service.  Direct shipments to the factory will be

accepted at the discretion of the company.  Coda Technologies, Inc. products
purchased outside of the U.S. will be covered by those warranty conditions extended by
the importing distributor which may differ in some respects from those given above.
Warranty service, if required,  is the responsibility of the importing distributor.  If a Coda
Technologies, Inc. product is removed from the country of original purchase, Coda
Technologies, Inc. distributors or dealers are not obligated by the conditions of this
warranty and repairs will be affected at their discretion.

III. Exclusion of Coverage- At the sole opinion of Coda Technologies, Inc. the following
situations are specifically excluded from coverage:

1. Any Amplifier 10.5 not operated in accordance with the instructions contained in this
manual, or otherwise subjected to abuse, tampering, modification, accidental damage,
or serial number defacement.

2. Damage to other property caused by any defects in this product, damages based
upon inconvenience, loss of use of the product, loss of time, commercial loss, or any other
damage whether incidental, consequential, or otherwise.

3. It is Coda Technologies,  Inc.  policy to extend coverage when reasonable doubt exist;
however, freight charges will be billed for any units returned under warranty and found
by the company to be operating according to specification.

This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.

Coda Technologies, Inc. continually researches new techniques, designs, and construction
methods and so reserves the right to introduce refinements into current product lines
without notice or obligation.  The company may offer product modifications to make
these refinements available to earlier production units.

Summary of Contents for Amplifier 10.5



















Reviews: