manualshive.com logo in svg

Coda Amplifier 10.5, Operation Manual, Page: 13 / 18

Share
Download
Coda Amplifier 10.5 Operation Manual Download Page 13

12

TECHNICAL  DATA

AMPLIFIER  10.5

Rated Power:                      100 Watts with 25 Watts class A @ 8 Ohms both channels driven from 20Hz to 20kHz
Frequency Response:        DC to -3dB @ 100kHz
Distortion:                             < .1 percent from 10Hz  to 20kHz @ 100 Watts  both channels driven into
                                               2  Ohm  through  8  Ohms
Gain:                                    26dB
Maximum Current:              >80 Amperes peak per channel
Noise:                                   -100dB referenced to rated output
input Impedance:              50k Ohms unbalanced/1k Ohms balanced
Output Impedance:           .05 Ohms from 20Hz to 20kHz

BRIDGED

Rated Power:                      400 Watts with 25 Watts class A @ 8 Ohms mono from 20Hz to 20kHz
Frequency Response:        DC to -3dB @ 100kHz
Distortion:               < .1 percent from 10 Hz to 20kHz @ 400 Watts driven into 2 Ohms through
                                               8  Ohms
Gain:                                    32dB
Maximum Current:              >80 Amperes peak
Noise:                                   -100dB referenced to rated output
Input Impedance:              1k Ohms unbalanced/1k Ohms balanced
Output Impedance:           .1 Ohms from 20Hz to 20kHz

SUPPLY    

                               

1000 VA toroidal power transformer and 120,000 uF of capacitance

DIMENSIONS

Height:                                 5.25" Faceplate,  6.0" Overall
Width:                                  19.0" Faceplate,  17.0" Chassis
Depth:                                 12.5" Overall
Weight:                                 45 lbs.,  50 lbs.,  Shipping
Power requirement:            450 Watts maximum at rated power

Summary of Contents for Amplifier 10.5



















Reviews:

No comments