Coda 40.0 Operation Manual Download Page 2

!

CAUTION

CAUTION

WARNING

WARNING

!

                                                 SERVICING TO QUALIFIED SERVICE

                                       CAUTION

:  TO PREVENT ELECTRIC SHOCK,

                                                 DO NOT REMOVE COVER.  NO USER

                                                 SERVICEABLE PARTS INSIDE,  REFER

                                                 PERSONNEL.

THIS SYMBOL IS INTENDED TO ALERT
YOU OF THE PRESENCE OF IMPORTANT
OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE LITERATURE
ACCOMPANYING THE UNIT.

THIS SYMBOL IS TO ALERT YOU OF THE
PRESENCE OF UNINSULATED DANGER-
OUS VOLTAGE WITHIN THE UNIT'S
ENCLOSURE THAT MAY BE OF SUFFI-
CIENT MAGNITUDE TO CONSTITUTE A
RISK OF ELECTRIC SHOCK.

                     WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE. TO
AVOID ELECTRICAL SHOCK,  DO NOT OPEN THE
UNIT.  REFER SERVICING TO QUALIFIED PERSONNEL.

Never install or remove the power cord from the

 

chassis

unless it has been disconnected from the AC power source
first.
Never pull on the power cord when removing it from an AC
power source. Grasp it by the plug.
Do not leave the power cord connected to an AC power
source unless it is connected to the unit.
It is recommended that during extended periods of nonuse
the unit's power cord be unplugged from its AC power
source.
Route the AC power cord so that it will not be damaged or
walked on.

CAUTION -

-

-

-

-

SAFETY PRECAUTIONS

1

Summary of Contents for 40.0



















Reviews: