background image

Listening for a Response

 

Release the 

Talk

 button to receive incoming 

transmissions. Your microTALK

®

 radio is always in 

Standby

 mode while the

 Talk

 buttons are not pressed.

To Adjust Volume

 

Press the 

Up 

or 

Down

 button to increase or decrease the 

volume. There are 13 different volume levels.

 

Do not hold the radi

o close to your ear. If the volume is 

set to an uncomfortable level, it could hurt your ear.

Auto Squelch/Maximum Range

Your microTALK

®

 radio will automatically shut off weak transmissions and 

unwanted noise due to terrain, conditions limit.

microTALK

®

 Range

 Your range will vary depending on terrain and conditions.
 

In flat, open country your radio will operate at maximum 

range.

 

Buildings and foliage in the path of the signal can reduce 

the range of the radio.

 

Dense foliage and hilly terrain will further reduce the 

range of the radio.

 

On Channels 8 through 14, your radio automatically 

switches to low power, which will limit the range the 
radio can communicate.

Turning On your Radio

Press and hold the 

Power/Menu

 button until you hear a series of audible tones 

indicating the radio is on.

 

1.

  After the radio chirps, the current channel number and 

user adjusted privacy code setting (if any) prompted. 

 

  Your microTALK

®

 radio is now in Standby mode, ready 

to receive transmissions. The radio is always in 
Standby mode except when the 

Talk

 or 

Power/Menu

 

buttons are pressed.

 

2.

 In Standby mode, 

Green

 LED flashes every 5 seconds.

Battery Low 

 

When battery power is low,

 Red

 LED flashes every 5 seconds. Voice prompt 

"

Please charge

" will be heard approximately 30 minutes before device 

automatically powers off. Your batteries should be recharged. It normally takes 
about 6 hours to fully charge batteries.

Auto Battery Save   

If there are no transmissions within 10 seconds, the radio will automatically 
switch to 

Battery Save

 mode. This will not affect the radio’s ability to receive 

incoming transmissions.

Communicating with Another Person 

 

1.

 Press and hold the 

Talk

 button.

 

2.

 With the microphone about two inches (5 cm) from 

your mouth, speak in a normal voice.

 

3.

 Release the 

Talk

 button when you finished talking and 

listen for a response.

 

You cannot receive incoming calls while pressing the 

Talk

 button. 

6

7

Power/Menu button

Up(+)/Down(-) 

Buttons

Two Inches
from Mouth

Listening

Maximum Range

Reduced Range

Reduced Range

Talk Button

Both radios must be tuned to the same 

channel/privacy code to communicate.

Green LED Flashes

Summary of Contents for microTALK PX280















Reviews: