Cobra microTALK PX280 Owner'S Manual Download

Page: 12 / 14

MODEL PX280:

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: 1) This device may not cause harmful interference, and
2) this device must accept any interference received,including interference that
may cause undesired operation.
FCC Warnings: Replacement or substitution of transistors, regular diodes or other
parts of a unique nature, with parts other than those recommended by Cobra may
cause a violation of the technical regulations of part 95 of the FCC rules, or
violation of type acceptance requirements of part 2 of the rules.

IMPORTANT NOTICE:

WARNING:

Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: 1) This device may not cause harmful interference, and 2) this device must
accept any interference received,including interference that may cause undesired operation.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Safety Information for microTALK

Radios

Your wireless handheld portable transceiver contains a low power transmitter. When the talk
button is pushed, it sends out radio frequency (RF) signals. The device is authorized to
operate at a duty factor not to exceed 50%. In August 1996, the Federal Communications
Commissions (FCC) adopted RF exposure guidelines with safety levels for handheld wireless
devices

Important

FCC RF Exposure Requirements: For body-worn operation, this radio has been tested and
meets the FCC RF exposure guidelines when used with Cobra accessories supplied or
designated for this product. Use of other accessories may not ensure compliance with FCC
RF exposure guidelines. Use only the supplied antenna. Unauthorized antennas,

modifications or attachments could damage the transmitter and may violate FCC

regulations.

Normal Position

Hold the transmitter approximately 2 inches from your face and speak in a normal voice,

with the antenna pointed up and away.

FCC Part 15.21 Warning Statement-
NOTE:

THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT

EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH
MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

IC RSS-GEN

This device complies with ISED license-exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the
device.

Under ISED regulations, this radio transmitter may only operate using an antenna of a type
and maximum (or lesser) gain approved for the transmitter by ISED. To reduce potential

radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication.
The applicant is responsible for providing proper instructions to the user of the radio device,
and any usage restrictions, including limits of exposure durations. The user manual shall
provide installation and operation instructions, as well as any special usage conditions, to

ensure compliance with SAR and/or RF field strength limits. For instance, compliance

distance shall be clearly stated in the user manual.

Radiation Exposure Statement:

Any Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

For Remote controller, SAR tests are conducted using standard operating positions accepted

by the FCC/ISED with the device transmitting at its highest certified power level in all tested

frequency bands, although the SAR is determined at the highest

certified power level, the

actual SAR level of the device while operating can be well below the maximum value.

Before a new model device is available for sale to the public, it must be tested and certified

to the FCC that it does not exceed the exposure limit established by the FCC/ISED, Tests for

each device are performed in positions and locations (e.g. at the ear and worn on the body)

as required by the FCC/ISED.
For body worn operation, this model device has been tested and

meets the FCC/ISED RF

exposure guidelines when used with an accessory designated for this product or when used

with an accessory that Contains no metal and that positions the handset a minimum of 10

mm from the body.
Non-compliance with the above restrictions may result in violation of RF exposure
guidelines.

In front of face at least 25mm, manxmum duty cycle 50%, compliance

with the public envionment etc.

This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.The device can be used in portable exposure

condition without restriction.

rmal Position

Pour maintenir le respect des lignes directrices du Canada,Ce dispositif doit
être installé et fonctionner à une distance minimale de 20 centimètresEntre
le radiateur et votre corps.