Customer Assistance
Warranty
Introduction
1
19
9
N
No
otth
hiin
ng
g
Comes Close to a Cobra
®
O
Op
pe
erra
attiio
on
n
1
18
8 E
En
ng
glliis
sh
h
M
Mo
od
de
e F
Fu
un
nc
cttiio
on
ns
s
Memory Location Scan
••
Your microTALK
®
radio can automatically scan up to
10 programmed
Memory Locations
.
If there are one or fewer memory locations
programmed in your radio, the scan memory
locations option will not be available. To program
at least two memory locations, see program
memory locations on page 12.
To scan memory locations:
1.
Press the
Mode/Lock
button until the
Scan
icon,
Memory
icon and the memory location
number flash on the display.
2.
Press the
Channel Up
or
Channel Down
button to begin scanning memory locations.
The
Scan
icon and the
Memory
icon will
continue to be displayed when memory
location scan is
on
. Your radio will continue
to scan memory locations and stop if an
incoming transmission is detected. Your
radio will remain on that memory location
for 10 seconds.
While setting memory location scan, if you
do not press any buttons for 15 seconds,
your radio will automatically return to
Standby
mode on the channel/privacy code
displayed before you entered mode functions.
During memory location scan (while receiving an Incoming
transmission), you can choose from the following:
a.
Press and hold the
Talk
button to communicate on that
memory location. Your radio will remain on that memory
location and after 10 seconds of no activity, radio will start
memory location scan again.
b.
Press the
Channel Up
or
Channel Down
button to resume
scanning memory locations.
If you press the
Talk
button while scanning, but more than
10 seconds after receiving a transmission, you will transmit on
the memory location on which, during scanning, you last received
a transmission. This will return the radio to
Standby
mode.
If you do not press any button within 10 seconds, your radio
will automatically resume scanning memory locations.
During memory location scan (while not receiving a
transmission), you can choose from the following:
a.
Press and hold the
Talk
button to communicate on the
channel/privacy code that was displayed before you entered
mode functions or memory location on which, during
scanning, you last received a transmission.
b.
Press the
Mode/Lock
button to proceed to other functions.
c.
Press the
Enter/Hi•Low
button to return to
Standby
mode
on the channel/privacy code that was displayed before you
entered mode functions or the memory location on which,
during scanning, you last received a transmission.
To reduce the number of memory locations being scanned,
you may de-program any unwanted locations. (See page 14
to de-program a memory location.)
10 Call Tone Settings
••
You can choose from 10 different call tone settings to transmit
a unique call alert.
To change a call tone setting:
1.
Press the
Mode
button until the letter “C” and
the current call tone number (01 through 10)
is displayed.
2.
Press the
Channel Up
or
Channel Down
button to hear the other call tone settings.
3.
Choose one of the following:
a.
Press the
Mode/Lock
button to enter the
new setting and proceed to other functions.
b.
Press the
Enter/Hi•Low
button to enter the
new setting and return to
Standby
mode.
O
Op
pe
erra
attiio
on
n
M
Mo
od
de
e//L
Lo
oc
ck
k B
Bu
utttto
on
n
C
Ca
allll T
To
on
ne
e S
Se
ettttiin
ng
g
C
Ch
ha
an
nn
ne
ell B
Bu
utttto
on
ns
s
S
Sc
ca
an
nn
niin
ng
g L
Lo
oc
ca
attiio
on
ns
s
M
Mo
od
de
e//L
Lo
oc
ck
k B
Bu
utttto
on
n
C
Ch
ha
an
nn
ne
ell B
Bu
utttto
on
ns
s
