While setting privacy code scan, if you do not press any buttons
for 15 seconds, your radio will automatically return to
Standby
mode on the channel/privacy code that was displayed before
you entered mode functions.
During privacy code scan (while receiving an incoming
transmission), you can choose from the following:
a.
Press and hold the
Talk
button to communicate on
that channel/privacy code. Your radio will remain on
that channel/privacy code and return to
Standby
mode.
b.
Press the
Channel Up
or
Channel Down
button to
resume scanning privacy codes.
If you press the
Talk
button while scanning, but more than
10 seconds after receiving a transmission, you will transmit
on the channel/privacy code on which you last received a
transmission. This will then return the radio to
Standby
mode.
If you do not press any button within 10 seconds, your
radio will automatically resume scanning privacy codes.
During privacy code scan (while not receiving a transmission),
you can choose from the following:
a.
Press and hold the
Talk
button to communicate on
the channel/privacy code that was displayed before you
entered mode functions or the channel/privacy code on
which, during scanning, you last received a transmission.
This will return the radio to
Standby
mode.
b.
Press the
Mode/Lock
button to proceed to set memory
location scan (see page 18 for further details).
c.
Press the
Enter/Hi•Low
button to return to
Standby
mode on the channel/privacy code that was displayed
before you entered mode functions or the channel/
privacy code on which, during scanning, you last
received a transmission.
Customer Assistance
Warranty
Introduction
1
17
7
N
No
otth
hiin
ng
g
Comes Close to a Cobra
®
O
Op
pe
erra
attiio
on
n
1
16
6 E
En
ng
glliis
sh
h
M
Mo
od
de
e F
Fu
un
nc
cttiio
on
ns
s
During channel scan (while not receiving a transmission),
you can choose from the following:
a.
Press and hold the
Talk
button to communicate on the
channel or channel/privacy code that was displayed before
you entered mode functions or the channel on which, during
scanning, you last received a transmission. This will then
return the radio to
Standby
mode.
b.
Press the
Mode/Lock
button to proceed to set privacy
code scan on the channel that was either displayed before
you entered mode functions or on which, during channel
scanning, you last received a transmission (see below for
further details).
c.
Press the
Enter/Hi•Low
button to return to
Standby
mode
on the channel/privacy code that was displayed before you
entered mode functions or the channel on which, during
scanning, you last received a transmission.
Privacy Code Scan
••
Your microTALK
®
radio can automatically scan the
Privacy Codes
(01 through 38) within one channel.
To scan privacy codes:
1.
While in
Standby
mode, press the
Channel Up
or
Channel Down
button
to choose the channel on which you
wish to scan privacy codes.
2.
Press the
Mode/Lock
button until the
Scan
icon and the privacy code numbers
flash on the display.
3.
Press the
Channel Up
or
Channel Down
button to begin scanning privacy codes
within the channel you selected.
The
Scan
icon will continue to be displayed
when privacy code scan is
on
. Your radio will
continue to scan privacy codes and stop as an
incoming transmission is detected. Your radio
will remain on that channel/privacy code for
10 seconds.
O
Op
pe
erra
attiio
on
n
C
Ch
ha
an
nn
ne
ell B
Bu
utttto
on
ns
s
M
Mo
od
de
e//L
Lo
oc
ck
k B
Bu
utttto
on
n
S
Se
elle
ec
ctt C
Ch
ha
an
nn
ne
ell
S
Sc
ca
an
n P
Prriiv
va
ac
cy
y C
Co
od
de
es
s
