background image

To temporarily turn off auto squelch:

Press the 

Light/Max Range

 button for  

less than five seconds. 

To turn maximum range extender on:

  Press and hold the 

Light/Max Range

 button  

for at least five seconds until you hear  

two beeps which indicates the maximum 

range extender is 

on

.

To turn maximum range extender off:

  Press and release the 

Light/Max Range

  

button or change channels.

Lock Function 

The 

Lock

 function locks the 

Channel Up

,

 Channel 

Down

 and 

Mode/Power

 buttons to prevent 

accidental operation. 

To turn the lock on or off:

   Press and hold the 

Lock

 button for  

two seconds.

A double beep sound is used to confirm your lock 

on

 or

 off 

request. When in 

Lock 

mode,  

the 

Lock

 icon will be displayed.

Customer Assistance Warranty

Introduction

Operation

Using Your Radio

Operation

Listening for a Response 

Release the 

Talk

 button to receive incoming 

transmissions. Your microTALK

®

 radio is always in 

Standby 

mode while the 

Talk

 or 

Call

 buttons are 

not pressed.

To Adjust Volume  

Press the 

Volume Up

 or 

Volume  

Down 

button.

A double beep sound is used to indicate  

the minimum and maximum volume levels  

(1 through 8).

Call Button 

 

Press and release the 

Call

 button. 

The other person will hear a two second call 

tone. This tone is used only to establish voice 

communications.

See page 12 on how to select between five 

call tone settings.

4

5

VO

LUME

CALL

MODE

CHANNEL

Volume Button

VO

LUME

CALL

MODE

CHANNEL

Call Button

Listening

Volume Level

Lock Icon

VO

LUME

CALL

MO

DE

CHANNEL

Light/Max Range

VO

LUME

CALL

MODE

CHANNEL

Lock Button

To Illuminate Display 

Press and release the 

Light/Max Range

 button  

to illuminate the display for 10 seconds.

Auto Squelch/Maximum Range 

Your microTALK

®

 radio will automatically shut 

off

 weak transmissions 

and unwanted noise due to terrain, conditions or if you’ve reached your 

Maximum Range

 limit.

You can temporarily turn 

off

 auto squelch or turn 

on

 maximum range 

extender, allowing all signals to be received and extending the maximum 

range of your radio.

VO

LUME

CALL

MO

DE

CHANNEL

Light/Max Range

microTALK

®

 Range 

Your range will vary depending on terrain and conditions.

In flat, open country your radio will  

operate at maximum range.
Buildings and foliage in the path of the  

signal can reduce the range of the radio.
Dense foliage and hilly terrain will further  

reduce the range of the radio.
On FRS Channels 8 through 14, your radio 

automatically switches to low power, which  

will limit the range the radio can communicate.

Remember, you can achieve maximum 

range by using maximum range extender. 

See page 4 for details.

V

O

LUM

E

CAL

L

MODE

CH

A

NNEL

V

O

LU

M

E

CAL

L

MODE

C

H

A

N

N

E

L

V

O

LU

ME

CAL

L

MODE

C

HA

N

NE

L

Maximum Range

Reduced Range

Reduced Range

Nothing 

Comes Close to a Cobra

®

CXT395_MANL.indd   4-5

3/15/13   9:29 AM

Summary of Contents for CXT395












Reviews: