Cobra CXT1095 FLT Owner'S Manual Download Page 9

Page: 9 / 13

VibrAlert

and Call Alert

•

Your microTALK

radio can alert you to incoming

signals by sounding an audible call tone, by

vibrating silently or both.

To change call settings:
1.

Press the

Mode

button until the

Call Setting

icon flashes on the display. The current setting

(“01” v ring, “02” ring only) is displayed.

Press the

Channel Up

Channel Down

button to

change the call setting.

Choose one of the following:

Press the

Mode

button to enter the new

setting and proceed to other functions.

Press

Talk

Call/Lock

button to enter the

new setting and return to

Standby

mode.

Do not press any buttons for 15 seconds to enter

the new setting and return to

Standby

mode.

Nothing

Comes Close to a Cobra

Ten Call Tone Settings

•

You can choose between ten different

Call Tone Settings

to transmit

a call alert.

To change a call tone setting:
1.

Press the

Mode/Power

button until the

letter “C” and the current call tone number

(01 through 10) is displayed. The current

call tone will sound for three seconds.

Press the

Channel

Down

button

to hear the other call tone settings.

Choose one of the following:

Press the

Mode/Power

button to enter the

new setting and proceed to other functions.

Press

Talk

Call/Lock

button to enter the

new setting and return to

Standby

mode.

Do not press any buttons for 15 seconds to enter

the new setting and return to

Standby

mode.

Call Tone Setting

Vox

HI MED LO WX

TW DCS Scan

CTCSS Mem

BURP Power Saver

Call Tone On/

Vibrate On

Vox

HI MED LO WX

TW DCS Scan

CTCSS Mem

BURP Power Saver

Call Tone On/

Vibrate Off

If “

” flashes in place of the privacy code numbers,

a privacy code is already set in the opposite (CTCSS
or DCS) system. Press the

Channel Up

Channel Down

button to cancel the opposite code and select a privacy

code from the active system for the selected channel.

Choose one of the following:

Press the

MEM/ESC

button to enter the channel/privacy code

in the selected memory location. Radio then proceeds to next

memory location, which will blink.

Press and hold the

MEM/ESC

button to save the current state of

the Set Memory Function and return to

Standby mode

To recall a stored memory channel location:
1.

Press the

MEM/ESC

button until the

Memory

icon and the memory location number flash on

the display.

Press the

Channel Up

Channel Down

button

to select a memory location (0 through 9).

If a location has been programmed before,

its associated channel/privacy code will be

shown on the display.

Press and hold the

MEM/ESC

button to return

Standby

mode

on the selected memory

location.

A memory location can be reprogrammed

at any time it is displayed. Press the

MEM/ESC

button to begin.

Vox

HI MED LO WX

TW DCS Scan

CTCSS Mem

BURP Power Saver

Memory Channel

MEM

ESC

TRI

WATCH

SCAN

LUME

CALL

MODE

CHANNEL

H-M-L

Channel Button

MEM

ESC

TRI

WATCH

SCAN

LUME

CALL

MODE

CHANNEL

H-M-L

MEM/ESC Button

MEM

ESC

TRI

WATCH

SCAN

LUME

CALL

MODE

CHANNEL

H-M-L

Channel Button

MEM

ESC

TRI

WATCH

SCAN

LUME

CALL

MODE

CHANNEL

H-M-L

Mode/Power

Operation

Mode Functions

Operation

Customer Assistance Warranty

Introduction

CXT1095_FLT_MANL.indd 12-13

12/20/13 2:40 PM

Summary of Contents for CXT1095 FLT














Search results

Summary of Contents for CXT1095 FLT

Reviews:

Related manuals for CXT1095 FLT

Brands by name

Popular brands

Cobra CXT1095 FLT, Owner'S Manual

Search results

Summary of Contents for CXT1095 FLT

Reviews:

Related manuals for CXT1095 FLT

Brands by name

Popular brands