background image

Lock Function 

The 

Lock

 function locks the 

Channel Up

,

 Channel 

Down, Volume Up, Volume Down

 and 

Mode/

Power

 buttons to prevent accidental operation. 

To turn the lock on or off:

   Press and hold the 

Call/Lock

 button for  

two seconds.

A double beep sound is used to confirm your lock 

on

 or

 off 

request. When in 

Lock 

mode,  

the 

Lock

 icon will be displayed.

Customer Assistance Warranty

Introduction

Operation

Using Your Radio

Operation

Listening for a Response 

 Release  the 

Talk

 button to receive incoming 

transmissions. Your microTALK

®

 radio is always in 

Standby 

mode while the 

Talk

 or 

Call

 buttons are 

not pressed.

To Adjust Volume 

 

 Press  the 

Volume Up

 or 

Volume  

Down 

button.

A double beep sound is used to indicate  

the minimum and maximum volume levels  

(1 through 8).

Call Button 

 

Press and release the 

Call

 button. 

The other person will hear a two second call tone. This 

tone is used only to establish voice communications.

See page 11 on how to select between ten 

call tone settings.

 

4

5

Listening

Volume Level

Lock Icon

RX

Vox

HI MED LO WX

TW DCS Scan

CTCSS Mem

LED/S.O.S. Flashlight 

 Press and release the 

LED flashlight 

button below 

the TALK button to use the LED flashlight located at 

the bottom of the radio.
To activate S.O.S. function, press and hold the 

LED 

flashlight button 

to turn on. Press and release to 

turn off the flashlight or S.O.S. function.

Auto Squelch 

Your microTALK

®

 radio will automatically shut 

off

 weak transmissions 

and unwanted noise due to terrain, conditions or if you’ve reached your 

Maximum Range

 limit.

microTALK

®

 Range 

Your range will vary depending on terrain and conditions.

In flat, open country your radio will  

operate at maximum range.
Buildings and foliage in the path of the  

signal can reduce the range of the radio.
Dense foliage and hilly terrain will further  

reduce the range of the radio.
On FRS Channels 8 through 14, your radio 

automatically switches to low power, which  

will limit the range the radio can communicate.

MEM

ESC

TRI

WATCH

SCAN

H-M-L

V

O

LU

ME

CA

LL

MODE

C

H

A

NN

E

L

MEM

ESC

TRI

WATCH

SCAN

H-M-L

V

O

LU

ME

CA

LL

MODE

CH

A

N

N

E

L

MEM

ESC

TRI

WATCH

SCAN

H-M-L

V

O

LU

ME

CA

LL

MODE

CH

A

NN

E

L

Maximum Range

Reduced Range

Reduced Range

Nothing 

Comes Close to a Cobra

®

MEM

ESC

TRI

WATCH

SCAN

V

O

LUME

CALL

MODE

CHANNEL

Volume Button

MEM

ESC

TRI

WATCH

SCAN

V

O

LUME

CALL

MODE

CHANNEL

Call Button

LED/S.O.S. Flashlight

MEM

ESC

TRI

WATCH

SCAN

V

O

LUME

CALL

MODE

CHANNEL

Lock Button

CXT1035CAMO_MANL_vE.indd   5-6

2/28/14   9:55 AM

Summary of Contents for CXT1035 FLT CAMO















Reviews: