Memory Location Scan Mode
During
Memory Location Scan
mode, the radio will rapidly
scan through all programmed memory channels. Whenever
any activity is detected on a channel, the radio will stop the
scan for 10 seconds to allow you to listen briefly on that
channel. It will then continue to scan unless you switch out of
Memory Location Scan
mode.
NOTE
If there are fewer than two memory locations programmed
in the radio, the
Memory Location Scan
option will not
be available. At least two memory locations need to be
programmed to use the Scan button.
To Enter Memory Location Scan:
1.
From
Marine Standby
mode, press the
Memory/Escape
button.
2.
Press and hold the
DUAL WATCH/SCAN
button.
The radio will immediately begin to scan all pre-assigned
memory channels. The
SCAN
and
MEM
icons will show on
the LCD.
3.
A signal on any channel will stop the scan for
10 seconds to allow you to listen to the traffic
on that location.
4.
Press the
Channel Up
or
Channel Down
button
to resume scanning the
Memory Location Scan
channels or to change the scan direction.
5.
To EXIT
Memory Location Scan
mode, press and hold the
DUAL WATCH/SCAN
button again. The
SCAN
and
MEM
icons will disappear from the LCD and the radio will return
to
Memory
mode.
VHF Marine Radio Protocols
Intro
Operation
Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
Caution
Warning
Installation
Customer
Assistance
Operating Your Radio
VHF Marine Radio Protocols
Intro
Operation
Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
Caution
Warning
Installation
Customer
Assistance
Operating Your Radio
25
Nothing
Comes Close to a Cobra
®
24 English
To Recall a Stored Memory Location:
1.
Press the
Memory/Escape
button. The
MEM
icon will be
turned On.
2.
Press the
Channel Up
or
Channel Down
button to select
the memory location. If a memory location has been
programmed, its associated channel will display on the
LCD. Your radio is now in
Marine Standby
mode on the
selected memory location.
To Exit Memory Location Mode:
Press the
Memory/Escape
button to return the radio
to
Marine Standby
mode. The last channel used in
Marine
Standby
mode will now be displayed on the
LCD and the
MEM
icon will disappear.
To Erase Stored Memory Locations:
1.
Press and hold the
Memory/Escape
button for two
seconds. The memory location number will start flashing
and the
MEM
icon will be turned On.
2.
Use the
Channel Up
and
Channel Down
buttons to advance
to the memory location you want to erase.
3.
Press the
Memory/Escape
button to select the memory
location. The memory channel number will stop flashing
and the channel number will start flashing.
4.
Use the
Channel Up
and
Channel Down
buttons to change
the channel to read “
--
” at the selected memory location.
5.
Press the
Memory/Escape
button to erase that memory
location.
Repeat steps 2 through 5 to erase as many additional memory
locations as you want.
6.
Press and hold the
Memory/Escape
button for two seconds.
This will return the radio to
Memory
mode.
7.
Press and release the
Memory/Escape
button again
to return to
Marine Standby
mode.
MEM Icon
Memory Location Scan
FLOATING MARINE HH150
ESC WEATHER SETUP
PWR
MEM
H-M-L
ENTER
CHANNEL
SC/DW
16+
VOL
VOL +
SUBMERSIBLE
MEM/ESC Button
FLOATING MARINE HH150
ESC WEATHER SETUP
PWR
MEM
H-M-L
ENTER
CHANNEL
SC/DW
16+
VOL
VOL +
SUBMERSIBLE
Scan Button
Advanced Operation
Advanced Operation
Intro
Operation
Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
Caution
Warning
Installation
Customer
Assistance
