Cobalt Digital Inc 9922-FS Product Manual Download Page 43 | Manualshive

Page: 43 / 118

Cobalt Digital Inc 9922-FS Product Manual Download Page 43

9922FS-OM (V1.5)

9922-FS PRODUCT MANUAL

3-1

Chapter 3

Chapter 3

Operating Instructions

Overview

This chapter contains the following information:

•

Control and Display Descriptions (p. 3-1)

•

Accessing the 9922-FS Card via Remote Control (p. 3-6)

•

Checking 9922-FS Card Information (p. 3-8)

•

Ancillary Data Line Number Locations and Ranges (p. 3-9)

•

9922-FS Function Menu List and Descriptions (p. 3-10)

•

Troubleshooting (p. 3-66)

Control and Display Descriptions

This section describes the user interface controls, indicators, and displays for
using the 9922-FS card. The 9922-FS functions can be accessed and
controlled using any of the user interfaces described here.

The format in which the 9922-FS functional controls, indicators, and displays
appear and are used varies depending on the user interface being used.
Regardless of the user interface being used, access to the 9922-FS functions
(and the controls, indicators, and displays related to a particular function)
follows a general arrangement of Function Menus under which related
controls can be accessed (as described in Function Menu/Parameter Overview
below).

Note:

When a setting is changed, settings displayed on DashBoard™ (or a Remote
Control Panel) are the settings as effected by the card itself and reported back
to the remote control; the value displayed at any time is the actual value as set
on the card.

If you are already familiar with

using DashBoard or a Cobalt

Remote Control Panel to control

Cobalt cards, please skip to

9922-FS Function Menu List and

Descriptions (p. 3-10).

«
...
41
42
43
44
45
...
»

Summary of Contents for 9922-FS























































































































Reviews:

No comments