manualshive.com logo in svg

Cobalt Digital Inc 9922-FS, Product Manual, Page: 108 / 118

Share
Download
Cobalt Digital Inc 9922-FS Product Manual Download Page 108

3

Troubleshooting

3-66

9922-FS PRODUCT MANUAL

9922FS-OM (V1.5)

Troubleshooting

This section provides general troubleshooting information and specific 
symptom/corrective action for the 9922-FS card and its remote control 
interface. The 9922-FS card requires no periodic maintenance in its normal 
operation; if any error indication (as described in this section) occurs, use this 
section to correct the condition. 

Error and Failure Indicator Overview

The 9922-FS card itself and its remote control systems all (to varying 
degrees) provide error and failure indications. Depending on how the 
9922-FS card is being used (i.e, standalone or network controlled through 
DashBoard™ or a Remote Control Panel), check all available indications in 
the event of an error or failure condition.

The various 9922-FS card and remote control error and failure indicators are 
individually described below.

Note:

The descriptions below provide general information for the various status and 
error indicators. For specific failures, also use the appropriate subsection 
listed below.

• Basic Troubleshooting Checks (p. 3-70)

• 9922-FS Processing Error Troubleshooting (p. 3-71)

• Troubleshooting Network/Remote Control Errors (p. 3-72)

Summary of Contents for 9922-FS























































































































Reviews:

No comments