Cobalt Digital Inc 232 Owner'S Manual Download Page 108 | Manualshive

Page: 108 / 136

background image

Cobalt_OM_preprint_shell.fm Page 2 Wednesday, March 1, 2006 5:39 AM

4

-

8

243 Owner’s Manual

COBALT

243

CUDDY

CABIN

S

ECTION

4

BATTERY CONNECTIONS

Loose battery connections can cause errant signals
to the boat’s electrical system.

Read and understand the safety information on or
supplied with your battery(ies). Maintain the
battery(ies) following the manufacturer’s
recommendations.

JUMP START STUDS

This receptacle allows for jump-starting an engine.
The receptacles have protective covers and must
stay in place when receptacles are not being used.
The covers identify the + positive (red) and the -
negative (black). The studs can be used to raise the
engine compartment when the batteries are low or
removed.

The jump start studs are located near or on the
battery switch panel.

1 – Receptacle

A

WARNING

Avoid the potential of explosion from
shorting or arching. Keep the battery
connections tight and clean, the
terminal covers in place and the
battery(ies) secure in the restraint
system.

COB_0090_A

NOTICE: Do not start an engine
from the jump start studs
without the batteries connected
to the boat’s charging system.
Damage to engine and charging
system will result.

1

2

ALL

OFF

HELM

BILGE PUMP

UM

COB_0100_A

1

«
...
106
107
108
109
110
...
»

Summary of Contents for 232









































































































































Reviews:

No comments

Related manuals for 232

Brand: Williams Pages: 57

2012 Gamefish series

Brand: Sea Hunt Pages: 32

Brand: Spitfire Pages: 10

Brand: Grady-White Boats Pages: 105

Brand: Grady-White Boats Pages: 126

SHIRE 14 130 WB

Brand: Barrus Pages: 50

Packraft FamilyRaft

Brand: Nortik Pages: 9

Brand: Nortik Pages: 11

Brand: Nortik Pages: 29

Performance H2X

Brand: Baja Pages: 83

Brand: RIOT Pages: 7

2503 Center Console

Brand: Trophy Pages: 56

Brand: TAKACAT Pages: 4

Brand: TAKACAT Pages: 5

Brand: Paddle King Pages: 11

Brand: Walker Bay Pages: 24

Brand: Sailfish Pages: 68

Brand: Quicksilver Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands