background image

 

HOW TO PROPERLY OPERATE AIR VALVE

 

ATTENTION: 

Do not use a compressed air source (i.e. 

automotive tire air compressor) to inflate boat. Over 

inflation through the use of compressed air may result 

in ruptured seams and will void the warranty. 

The valve has a special pushpin inside. Do not use any 
type of tool to adjust the position. Use your fingers! This 
pushpin has two positions, up and down. When it is 

pressed in the down position, air will escape. If you turn 
the pushpin in any direction it will pop up. This will lock 
air inside and prevent it from escaping through the valve. 

Before inserting the air pump tube into the valve, please 
make sure that the pushpin is in the upper, popped up 
position. Once the pin is in the "popped up" position, 

insert the air pump adapter into the valve and inflate. 
Once you remove the air pump, pressure will seal the 

valve and air will not escape. If you would like to deflate the boat, press down on 
the pushpin and turn it in any direction until it stays in the pressed down position. 

Air will immediately escape from the tubes thru the valve. 

 

INFLATION 

Inflate the boat with the pump supplied.  

NOTE: 

When using a hand pump, the 

boat cannot be over-inflated. If using an electric inflator inflate the boat to about 
80% and then finish the inflation procedure with the pump supplied. When 
inflating the boat with the hand pump, 

it is normal for the hand pump to 

leak some air where the adapter connects to the valve.

 Continue to pump 

until the tubes become hard. 

Never drag boat on pavement or 

concrete!

 

 

Depending on climate and operating conditions, the pressure may 

require monitoring during boat use to maintain a correct inflation 
level. What is 100% full & don't have a gauge?  

Inflate the tubes & floor 

until the hand pump becomes somewhat difficult to push down. 

 

Due to the boat having a safe valve to prevent over-pressure installed, 

a boat inflated for 4 to 5 days may lose pressure and require re-
inflation to correct operating pressure, this is normal. It doesn't mean 
that your boat has a leak; it means the safety over-pressure valve is 

protecting your boat! 

 

WARNING:  DO NOT 

using a compressed air 

source (i.e. compressor) to inflate the boat.  Over-
inflation with a compressor may result in ruptured 
seams and/or bulkheads. 

 

When inflating, maintain a balance of air between air chambers to 
prevent damage to air chamber bulkheads. 

Summary of Contents for M-CBX9.6 2016

















Reviews: