OWNER’S MANUAL
2021
If the primary pump is a 2-Speed Pump 1, Ready Mode (indicated
by R) will circulate water periodically, using Pump 1 Low, in order to
maintain a constant water temperature, heat as needed, and refresh
the temperature display. This is known as “polling.”
Rest Mode
(indicated by
R
) will only allow heating during
programmed filter cycles. Since polling does not occur, the
temperature display may not show a current temperature until the
primary pump has been running for a minute or two.
In
Rest Mode
, the spa will only heat to set temperature during
programmed filter times, even though the water is being filtered
constantly when in Circulation Mode.
Changing the Mode
Press and release the “Menu” button until “MODE” appears. Press
and release the “Up” or “Down” button to switch the Mode to
“Ready” or “Rest”. Press and release the “Menu” button to save the
Ready-in-Rest
Mode appears in the display if the spa is in Rest Mode and “Jets” is
pressed. It is assumed that the spa is being used and will heat to set
temperature. The primary pump will run until set temperature is
reached, or 1 hour has passed. After 1 hour, the System will revert
to Rest Mode. This mode can also be reset by entering the Mode
Menu and changing the Mode.
Show and Set Time-of-Day
Be sure to set the Time-of-Day Setting the time-of-day can be
important for determining filtration times and other background
features. When in the TIME menu, SET TIME will flash on the
display if no time-of-day is set in the memory.
Setting the Time
Press and release the “Menu” button until “TIME” appears. Press
and release the “Up” or “Down” to adjust the Hour. Press the “Menu”
button to save the hour and move on to the Minutes. Press and
release the “Up” or “Down” to adjust the Minutes. Press the “Menu”
button to save
the Minutes.
Note:
If Time of Day is not actually programmed due to a power
cycle, SET TIME will appear in the menu instead of just TIME.
Hold (Standby)
Hold Mode is used to disable the pumps during service functions
like cleaning or replacing the filter. Hold Mode will last for 1 hour
unless the mode is exited manually.
Selecting Hold Mode
Press and release the “Menu” button until “HOLD” is on the screen.
Press and release the “Up” or “Down” button to activate “Hold
Mode”. The screen will display HOLD, ING, FOR, and the time
remaining.
Flip (Invert Display)
Changing the Screen Orientation
Press and release the “Menu” button until “FLIP” is on the
screen. Press and release the “Up” or “Down” button to invert
the display. Press and release the menu button to save this
setting.
Restricting Operation
The control can be restricted to prevent unwanted use or
temperature adjustments.
Locking the panel prevents the
controller from being used, but all automatic functions are still
active.
Locking the Temperature allows Jets and other
features to be used, but the Set Temperature and
other programmed settings cannot be adjusted.
Temperature Lock allows access to a reduced selection of
menu items. These include Set Temperature, FLIP,
UTIL,
INFO and FALT LOG.
Restricting Operation
Press and release the “Menu” button until “LOCK” is on the
screen. Press and release the “Up” or “Down” button to enter
the menu. Press and release the “Menu” button to switch from
“TEMP” to “PANL”.
Note:
Pressing and releasing the
“Menu” button again will take you back to the beginning of the
“LOCK” menu. With “TEMP” or “PANL” selected press and
release the “Up” or “Down” button to change the menu
selection to the “OFF”/”ON” option. Press and release the
“Up” or “Down” button to change the menu option from
“OFF” to “ON” to lock either the “TEMP” to “PANL”. Press
and release the “Menu” button to save the “LOCK” setting.
Unlocking
This Unlock sequence may be used from any screen that may
be displayed on a restricted panel.
Unlocking instructions
While pressing and holding the Temperature Button (UP
button or Up button), slowly press and release the
“Menu” button two times.
Adjusting Filtration
Filter cycles are set using a start time and a duration. Start
time is indicated by an “A” or “P” in the bottom right corner of
the display. Duration has no “A” or “P” indication. Each setting
can be adjusted in 15-minute increments. The panel
calculates the end time and displays it automatically.
2
8
TRADITIONAL SPAS
