E-9
NOTE :
ALTHOUGH THIS PRODUCT IS FULLY COMPATIBLY WITH USB 1.1 & 2.0 STANDARDS,
A SMALL PERCENTAGE OF USB FLASH DRIVES MIGHT NOT BE READABLE,
DUE TO THOSE USB-FLASH DRIVE MANUFACTURERS NON-COMPLIANCE WITH
THE FULL (OFFICIAL) USB 1.1 / 2.0 STANDARDS.
IMPORTANT
REMOVAL OF USB DRIVES & SD-CARDS NEVER REMOVE (OR UNPLUG)
USB-DRIVES OR SD-CARDS FROM THE SET DURING PLAYBACK OF MP3 SONGS
FROM THESE MEDIA. ALWAYS PRESS STOP FIRST AND THEN PRESS THE CD
KEY TO SWITCH TO "CD" MODE BEFORE REMOVING OR UNPLUGGING USB
MEMORY, TO PREVENT DAMAGE TO YOUR SONG FILES OR MEMORY DEVICES.
E-10
- THE CD PLAYER CAN BE PROGRAMMED TO PLAY ANY SEQUENCE OF UPTO 60
TRACKS, AS DESIRED.
- ALWAYS PRESS THE KEY BEFORE STARTING THE PROGRAMMING.
- PRESS THE KEY (18) ONCE. THE SET IS NOW IN "MEMORY PROGRAMMING
MODE".
- THE DISPLAY WILL APPEAR AS SHOWN BELOW:
- PRESS THE NEXT OR BACK TO SELECT THE TRACK (SONG) NUMBER YOU WISH TO
BE STORED IN THE CURRENT MEMORY (PROGRAM) LOCATION.
- PRESS THE KEY (18) ONCE TO CONFIRM YOUR SELECTION.
- REPEAT THE PREVIOUS 2 STOPS, EACH TIME SELECTING ANY TRACK NUMBER OF
YOUR CHOICE TO BE STORED IN SUCCESSIVE (PROGRAM) LOCATIONS.
- AFTER A MAXIMUM OF 60 SONGS (OR LESS) HAVE BEEN SELECTED AS DESCRIBED
ABOVE, PRESS (PLAY) KEY, THE DISPLAY WILL NOW SHOW 'PROG" TO INDICATE
YOU HAVE SAVED A PROGRAM-MEMORY.
- THE CD-PLAYER WILL PLAYBACK THE 'SAVED SEQUENCE" IN THE PROGRAM MEMORY.
- TO CLEAR (CANCEL) THE ENTIRE PROGRAM WHICH IS STORED IN THE MEMORY,
SIMPLY PRESS KEY TWICE (2 TIMES CONSECUTIVELY). THIS WILL RESET
THE MEMORY & CLEAR THE PROGRAM.
PROG
STOP
PROGRAMMING THE CD-PLAYER
STOP
PROG
000
MP3
3-DIGITS FLASHING
(TRACK/ SONG NUMBER)
P 01
VOL
MEMORY PROGRAM LOCATION
(P-01 = 1st LOCATION)
3D-VIRTUAL SURROUND
USB DRIVE AND SD-CARD FLASH MEMORY MP3 PLAYBACK
- THIS UNIT IS EQUIPPED WITH A USB SOCKET WHICH CAN ACCEPT AND PLAY MP3
FILES STORED ON STANDARD USB FLASH DRIVES (ALSO KNOWN AS "PEN DRIVES")
WHICH ARE FOR MEMORY STORAGE. (COMPATIBLE WITH USB VERSION 1.1 & 2.0).
- THIS UNIT IS ALSO EQUIPPED WITH AN SD CARD SOCKET WHICH CAN ACCEPT
AND PLAY MP3 FILES STORED ON STANDARD "SD CARDS
WHICH ARE USED FOR
MEMORY STORAGE.
- THE USB AND SD-CARD SOCKETS ARE LOCATED ON THE FRONT OF THE UNIT AS
SHOWN IN THE PICTURE BELOW.
- TO UTILIZE USB DRIVES/ SD-CARDS FOR MP3-PLAYBACK, INSERT THE USB DRIVE
OR SD-CARD INTO THE APPROPRIATE SOCKET (DEPENDING ON WHICH ONE YOU
ARE USING).
- THEN PRESS THE
USB/SD
BUTTON (ONCE FOR "USB" & TWICE FOR "SD-CARD").
- THE DISPLAY WILL SHOW THE "
USB
" OR
"SD"
SYMBOL & WILL CHECK IF ANY MP3
SONG FILES ARE FOUND.
- IF MP3 FILES ARE FOUND, THE SET WILL START PLAYBACK OF THE FIRST MP3
SONG FILE & THE DISPLAY WILL INDICATE THE TRACK NUMBER JUST LIKE
A MP3-CD PLAYBACK.
- PLAYBACK CONTROL (PLAY, PAUSE, BACK, NEXT, STOP) ARE ALSO EXACTLY SAME
AS WITH A MP3-CD DISC.
- YOU MAY ALSO USE THE
: "PROGRAMMING THE CD-PLAYER".
- TO CHANGE THE PLAYBACK MODE BACK TO "CD", PRESS THE
CD
BUTTON UNTIL
THE "CD" SYMBOL APPEARS IN THE DISPLAY. THE SET WILL THEN READ THE CD
DISC & START CD PLAYBACK AS USUAL.
SKIP + 10
KEY AND
FOLDER
KEY IN THE SAME MANNER
AS WITH MP3-CD PLAYBACK.
- YOU CAN ALSO PROGRAM THE PLAYBACK OF UPTO 60 MP3 TRACKS (SONGS)
SIMPLY FOLLOW THE SAME PROCEDURE AS DESCRIBED IN THE
PREVIOUS SECTION
USB PEN-DRIVE
SD CARD
IMPORTANT:
THIS UNIT DOES NOT SUPPORT USB-MP3 PLAYER, DUE TO THEIR
INHERENT LACK OF SOFTWARE COMPATIBILITY. ONLY USB "PEN DRIVES"
(FLASH MEMORY USB DRIVES) CAN BE USED, FOR MP3 PLAYBACK.
