manualshive.com logo in svg

Clipper CM 501 HONDA, Operating Instructions Manual, Page: 8 / 24

Share
Download
Clipper CM 501 HONDA Operating Instructions Manual Download Page 8

VERS. 2017.06.21 

CM 501 TH_MAN_EN 

8 

2 

MACHINE DESCRIPTION 

 
Any modification, which could lead to a change in the original characteristics of the machine, may 
be done only by Saint-Gobain Abrasives who shall confirm that the machine is still in conformity with 
the safety regulations. 

2.1  Short description 

 
The CM501 block saw is designed for durability and high performance for onsite wet and dry cutting 
operations of a wide range of masonry, refractory and natural stone products. 
As with all other NORTON products, the operator will immediately appreciate the attention given to 
detail  and  quality  of  materials  used  in  construction.  The  machine  and  its  component  parts  are 
assembled to high standards assuring long life and minimum maintenance. 

2.2  Purpose of use 

 
The  machine  is  designed  for  cutting  a  large  range  of  building  and  refractory  materials.  It  is  not 
designed for cutting wood or metals. 

2.3  Layout 

 

 

Summary of Contents for CM 501 HONDA

























Reviews:

No comments