background image

 

 

 

Part Number

Comments

Inspector Name

Date

MODEL NUMBER:

DATE OF MANUFACTURE:

Inspection:

O

ffi

cial periodic inspection must be made at least semiannually. The inspection must be performed by a 

quali

fi

ed person other than the intended user. If severe weather or conditions exist then inspections must be 

carried out more frequently. All inspection results must be logged in the space provided above.

 

 

1.

  Inspect swivel to make sure it is 

fl

ush with mounting surface.

 

2.

  Make sure all labeling is a

ffi

xed to the unit.

 

3.

  Make sure the unit can rotate 360° and D-ring can 

fl

ip from side to side.

 

4.

  When reusing a previously drilled hole, inspect for for debris or wallowing.

 

5. 

 Record inspection results in the space provide above.

*If any damage that could a

ff

ect the strength or operation of the device, or unsafe condi-

tions are found, proper disposal is required. The anchorage connector must be rendered 

unusable and then properly discarded.

MAINTENANCE, CLEANING AND STORAGE

Cleaning periodically will prolong the life and proper functioning of the product. The frequency 

of cleaning should be determined by inspection and by severity of the environment. Clean with 

compressed air and/or a sti

ff

 brush using plain water or a mild soap and water solution. Do not use 

any corrosive chemicals that could damage the product. Wipe all surfaces with a clean, dry cloth 

and hang to dry, or use compressed air. When not in use, store anchorage connectors in a cool, dry, 

clean environment, out of direct sunlight and free of corrosive or other degrading elements.

INSPECTION AND MAINTENANCE LOG

Summary of Contents for SWY100N-MTU













Reviews: