<
<
N
N
O
O
T
T
E
E
>
>
After you have set one function by sliding the DIP switch, you have to press Test Button to confirm the setting.
Only
1
switch of Dip Switch 1~4 can be set to ON position at a time.
A
A
c
c
c
c
e
e
s
s
s
s
o
o
r
r
i
i
e
e
s
s
I
I
n
n
c
c
l
l
u
u
d
d
e
e
d
d
a) 1 Magnet
b) 2 White Caps
c) 2 Screws
d) 2 Wall Plugs
L
L
E
E
D
D
I
I
n
n
d
d
i
i
c
c
a
a
t
t
o
o
r
r
The LED will light up in the following situations:
When the Universal Transmitter is activated by connected device.
When the cover is opened and the tamper switch is violated.
The LED indicator will flash twice when receiving acknowledge from the Control Panel.
B
B
a
a
t
t
t
t
e
e
r
r
y
y
The Universal Transmitter uses one
CR2 3V Lithium battery
as its power source. Please note:
ALWAYS
replace
battery with the correct size and voltage.
When the Universal Transmitter is low in battery, the LED will flash and a low battery signal will be sent to the Control
Panel along with regular signal transmissions for the Control Panel to display the status accordingly.
When changing batteries, after removing the old batteries, press the Tamper Switch twice to fully discharge before
inserting new batteries.
S
S
u
u
p
p
e
e
r
r
v
v
i
i
s
s
o
o
r
r
y
y
S
S
i
i
g
g
n
n
a
a
l
l
(
(
w
w
h
h
e
e
n
n
t
t
h
h
e
e
D
D
i
i
p
p
S
S
w
w
i
i
t
t
c
c
h
h
5
5
i
i
s
s
O
O
N
N
)
)
After installation, UT-15 will automatically transmit Supervisory Signals periodically to the Control Panel at random
intervals of 15-18 minutes.
Failure of the Control Panel to receive a preset Device Contact signal, the Control Panel will display the particular
Device Contact is experiencing an out-of-signal problem.
G
G
e
e
t
t
t
t
i
i
n
n
g
g
S
S
t
t
a
a
r
r
t
t
e
e
d
d
Remove the fixing screw and cover assembly.
Insert the “
CR2 3V
” battery into the battery holder connecting the polarity correctly.
Choose the type of connected device by sliding one Dip Switch on Universal Transmitter (Dip Switch 1, 2, 3, or 4) to
ON position and then press Test button to confirm settings.
Put the Control Panel into learning mode, refer to Control Panel manual for detail.
Press the Universal Transmitter’s test button.
Refer to Control Panel manual to complete the learn-in process.
After the Universal Transmitter is learned-in, place the Control Panel into (
Walk Test)
mode, hold the transmitter at
desired location, and press the Test button to test signal range.
Proceed with mounting and installation once you are satisfied that UT-15 location functions properly.
M
M
o
o
u
u
n
n
t
t
i
i
n
n
g
g
M
M
e
e
t
t
h
h
o
o
d
d
s
s
a
a
n
n
d
d
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
Step 1: Find a suitable location for mounting.
Step 2: Mounting:
(i) Use the mounting holes on the transmitter as a template of appropriate hole
positioning.
(ii) Use the provided wall plugs for plaster/brick installation.
(iii) Screw the transmitter into the provided wall plugs.
< Note >
Ensure the tamper switch spring is positioned so that it makes contact with the mounting
surface through the tamper switch aperture.
Step 3: Put the Control Panel into (
Walk Test)
Mode, and press the Test Button to test signal range
Step 4: Fit the white caps to the two mounting holes, installation is complete.
2
