background image

© 2008 Directed Electronics—all rights reserved

Owner recognition

 

Owner Recognition lets up to four users of the system have unique 

settings that meet their specific needs. It is almost like having four 

separate alarms in your vehicle, one for each user. This feature is 

only available to authorized dealers using the Bitwriter or Bitwriter 2 

program tool.  

Rapid resume logic

This Directed system will store its current state to non-volatile 

memory. If power is lost and then reconnected the system will recall 

the stored state from memory. 

For example, if the unit is in Valet Mode and the battery is discon-

nected for any reason, such as servicing the car, when the battery is 

reconnected the unit will still be in Valet Mode. This applies to all 

states of the system including arm, disarm, and Valet Mode.

Power saver mode

System

Your system will automatically enter Power Saver Mode while armed or 

in Valet Mode, after a period of time in which no operation has been 

performed. This lowers the current draw on the vehicle’s battery. Power 

Saver Mode takes over under the following conditions:

Power Saver when the system is armed:

 After the system has been 

armed for 24 hours the LED will flash at half its normal rate, decreasing 

the system’s current draw.

Summary of Contents for Responder LE 3.3X

























































Reviews: