background image

Smart Au toTest ing™

Each time you remotely arm the system, it tests all triggers and sensors. For

example, if  the

 Helmet Theft Prevention System is active, 

you will receive

the usual

 2 chirps and flashes

, then,

 5 seconds later

, there will be 

4 chirps

and 

4 flashes

. If a 

sensor

 is malfunctioning, you will receive the usual 2 chirps 

and 2 flashes, then, 

10 seconds later

, there will be 

4 chirps

 and 

4 flashes

Note that when you receive these indications that the system will still arm

even though a trigger or sensor is malfunctioning.

NOTE: Since this is a warn ing in di ca tion, you will hear

the 4 chirps even if you use the chirp muting feature.

n

Specific malfunction identification:

The system can also

indicate the 

specific

 trigger or sensor that is malfunctioning. If you get 

the 4-chirp/4-flash signal upon arming, perform the following to
identify the malfunctioning trigger or sensor:

1. Remotely disarm, then turn on the ignition. The LED status indicator will 

be flashing, pause, then repeat. 

 2. Count the number of flashes in one cy cle be tween pauses (for your

con ven ience, the flash cy cle re peats a to tal of 5 times) and re fer to the

fol low ing chart:

14

GP500

Summary of Contents for GP500





























Reviews: