background image

7

© 2004 directed electronics, inc.

panic mode

If you are threatened in or near your vehicle, you can attract attention

by triggering the system with your transmitter! If your factory keyless

transmitter does not have a panic button, this system can be pro-

grammed to enable a panic feature (refer to the Programming

Options).

If enabled, just press the lock button on your factory keyless transmit-

ter twice within three seconds to enter Panic Mode. The horn will

sound and the parking lights will flash for 30 seconds. To stop Panic

Mode at any time, press the unlock button on your factory transmitter.

nuisance prevention circuitry

®

Your system has Nuisance Prevention Circuitry

®

(NPC

®

). This circuitry

prevents annoying repetitive trigger sequences due to faulty door pin

switches or environmental conditions such as thunder, jackhammers,

airport noise, etc.

nnoottee:: The system can also be programmed so that pressing
the lock button twice within three seconds will activate an
optional accessory. If the unit is programmed to activate an
optional accessory, Panic Mode will not be operational.

nnoottee:: The remote Valet

®

feature will not work with all factory

keyless entry systems. Some keyless entry systems do not
work with a door open.

Summary of Contents for 22CX



















Reviews: