background image

AFTER SALES SUPPORT

 (AU) 1300 886 649  (NZ) 0800 836 761  |       [email protected]

9

Fig. 4

Instructions

The fan is equipped with 3 speeds and an oscillation option. To use the 
fan, follow the simple instructions below.
Place the fan on a dry, level surface where it will not overturn during use. 
Make sure the speed control at the back of the motor housing is in the 
OFF [ 0 ] position, then insert the power plug into an appropriate electrical 
outlet.

Speed selection

The speed control is located at the back of 
the motor housing (Fig. 4). To select the fan 
speed, move the speed control from the 
OFF [ 0 ] position to the desired setting:
0 = OFF - 1 = LOW - 2 = MEDIUM - 3 = HIGH

Oscillation

•  Press the oscillation knob on top of the 

motor housing to activate the oscillation 
function for widespread breeze 
distribution. The fan head will pivot from 
one side to the other. 

•  For stationary operation, pull up the oscillation knob when the air is 

blowing in the desired direction. 

CAUTION:

 Do not reach across the front of the fan when operating the 

oscillation control to avoid the possibility of your clothing, sleeves, etc. 
entering and getting caught in the front guard.

Tilt adjustment

The fan head assembly can be tilted to direct the breeze upwards or 
downwards to your desired angle. 
•    

CAUTION:

 Make sure the fan is unplugged from the power supply 

before adjusting the tilt angle.

•    Loosen both the larger tilt adjustment knob and the smaller tilt range 

knob. Tilt the head to the desired angle, and then tighten both knobs 
securely.

CAUTION:

 Do not tilt back the fan head further than it is intended to go. 

Doing so will damage the unit.

Summary of Contents for FT-30MD













Reviews: