background image

OPERATION

8

Tennant T300e/T300 (03- 2015)

MACHINE SYMBOLS

Solution flow (T300e)

ec-H2O scrubbing (option)

Circuit breaker

Do not lift by accessory rails

No step

Dual down pressure

(T300e)

No detergent (ec-H2O option)

Water temperature (ec-H2O option)

Battery charge

Fast speed (drive model)

Slow speed (drive model)

Parking brake

Forward / Reverse (drive model)

On

Off

No Solution flow (T300e)

CONTROL PANEL COMPONENTS

T300e Model Control Panel

3

1

2

4

1.

Service indicator

- Lights up when a machine or

charger fault is detected.

2.

Parking brake indicator

- Lights up when parking

brake lever is engaged. To turn off indicator,

disengage parking brake lever near left rear wheel.

3.

Battery discharge indicator (BDI)

- The battery

discharge indicator serves two functions. In normal

scrub mode it displays the charge level of the

batteries. It also, in conjunction when the service

indicator is flashing, provides specific LED codes

when a machine or charger fault is detected.

4.

ec-H2O indicator (Option)

- Lights up blue when

ec-H2O system is activated and operating

normally.

Summary of Contents for TENNANT T300
























































Reviews: