background image

OPERATION

Tennant T300e/T300 (03- 2015)

11

HOW THE MACHINE WORKS

Conventional scrubbing:

When using the conventional scrubbing mode, water

and detergent mixture from the solution tank flows to

the floor and the rotating brush(es)/pad(s) scrub the

floor clean. As the machine moves forward, the

squeegee with vacuum suction picks up the dirty

solution from the floor into the recovery tank.

ec-H2O NanoClean Technology (option):

When using the ec-H2O NanoClean technology, normal

water passes through a module where it is electrically

converted into a cleaning solution. The electrically

converted water attacks the dirt, allowing the machine

to easily scrub away the suspended soil. The converted

water then returns to normal water in the recovery tank.

BRUSH AND PAD INFORMATION

For best cleaning results use the appropriate brush or

pad for your cleaning application. Listed below are

brushes and pads and the applications for which each

is best suited.

NOTE: The amount and type of soilage play an

important role in determining the type of brush or pad

to use. Contact a Tennant representative for specific

recommendations.

Soft nylon bristle scrub brush (White) -

Recommended for cleaning coated floors without

removing finish. Cleans without scuffing.

Polypropylene bristle scrub brush (Black)

-

This general purpose polypropylene bristle scrub brush

is used for scrubbing lightly compacted soilage. This

brush works well for maintaining concrete, wood and

grouted tile floors.

Super abrasive bristle scrub brush (Gray) -

Nylon fiber impregnated with abrasive grit to remove

stains and soilage. Strong action on any surface.

Performs well on buildup, grease, or tire marks.

Polishing pad (White) -

Used to maintain highly polished or burnished floors.

Buffing pad (Red) -

Used for light duty scrubbing

without removing floor finish.

Scrubbing pad (Blue) -

Used for medium to

heavy-duty scrubbing. Removes dirt, spills, and scuffs

and leaves surface clean ready for recoating.

Stripping pad (Brown) -

Used for stripping of floor

finish to prepare the floor for recoating.

Heavy duty stripping pad (Black) -

Used for

aggressive stripping of heavy finishes/sealers, or very

heavy duty scrubbing.

Surface preparation pad (Maroon) -

Used for very

aggressive chemical free removal of floor finish to

prepare the floor for re-coating

Summary of Contents for TENNANT T300
























































Reviews: