background image

5.  Align the plastic lumber base (if needed) with the 

metal frame base and secure the plastic lumber to 
the frame base using the A-Angle brackets as 
shown, 

 

 

 

 

6. Read 

the 

MUST READ

 document and the anchoring 

information for the greenhouse. 

 

 

 
 

ANCHOR THE GREENHOUSE 
 

Strong winds will cause the greenhouse to shift. 

It must 

be anchored to the site. 

 
The site on which the greenhouse was constructed will 
determine the required anchoring method. Consult a 
professional contractor to determine the best and safest 
way to anchor the greenhouse. 
 

WARNING:

 To prevent property damage and serious 

personal injury, 

the assembled greenhouse must be 

anchored to the site.  READ THE MUST READ 
DOCUMENT. 
 
 
 
ANCHORING EXAMPLES 

 
The diagrams below illustrate two possible ways to 
properly anchor the shelter to the site. 
 
The parts shown in the diagrams below 

are not included 

with the shelter and must be purchased separately.  
 

Contact Customer Service at 1-800-245-9881 to 
purchase additional parts to anchor the shelter. 

ANCHORING SUGGESTIONS 

 

 

 

 

 

ATTENTION:

 After anchoring the greenhouse, read the 

Care and Maintenance information that follows. 

 

CONSULT THE MUST READ DOCUMENT FOR 
ADDITIONAL ANCHORING INFORMATION. 
 

 

 

Anchoring System 
when on concrete

Ground Anchoring 
System 

Visit www.ClearSpan.com for additional products and customer assistance.

15 of 16

Summary of Contents for Premium Solar Star 104918


















Reviews: