manualshive.com logo in svg

ClearSpan Premium Moo-Tel CD, Assembly Manual

Share
Download
ClearSpan Premium Moo-Tel CD Assembly Manual Download Page 15

15

Revision date: 07.03.14

CLEARSPAN

™

 PREMIUM MOO-TELS

The drop-down curtain requires a ribbon board to secure its 

upper section and a baseboard to secure its lower section. 

The materials for these components are not included and 

are 

supplied by the customer

.

BASEBOARDS AND RIBBON BOARDS

The example above shows the required ribbon board and 

baseboard as attached to the frame. 

 

ATTENTION:

 Consult the Main Cover Details diagram in 

the Quick Start section of this manual to determine where 

to install the ribbon board.

The ribbon board consists of two runs of material; the first 

is a 2" x 4" or 2" x 6" board attached to the building frame 

and the second is a 1" x 4" board attached to the first 

board. These boards, when assembled properly, provide 

a channel that secures the curtain when it is in the up or 

closed position. Boards are secured to the frame using the 

supplied 1/4" x 4" carriage bolts and to each other using the 

FA4652 supplied fasteners. 

Ribbon Board

Baseboard

Rafter

2" x 6" or 

2" x 4" Board

1" x 4" Board 

FA4652 

Wood 

Screws

1/4" x 4" 

Carriage 

Bolts

U-Channel

The diagram 

shows a customer- 

supplied ribbon 

board as attached 

to the frame

A customer-supplied baseboard and retaining board are 

also required to attach the curtain's lower edge. See the 

exploded view that follows.

The baseboard runs the length of the frame at ground level. 

The retaining board secures the curtain to the baseboard. 

The baseboard and retaining board are supplied by the 

customer.  

 

Fasteners (1/4" x 4" carriage bolts and FA4652 wood 

screws) are included. Depending on board width, use 2 

carriage bolts per rafter connection for the baseboard and 

ribbon board. Evenly space the wood screws at 24".

FRAME CHECK AND RIBBON BOARD INSTALLATION 

1.  Verify that the baseboard is installed properly at ground 

level. The baseboard must be level for the drop-down 

curtain to install and function properly.

2.  Gather the boards needed for the retaining board of the 

baseboard. See diagram above.

3.  Attach the first board of the two-piece ribbon board to 

the frame at the required height for the curtain.  See the 

main cover details diagram in the Quick Start section 

for the drop-down curtain height.

4.  Use the diagram to the left to install the second board 

of the ribbon board.  Attach to the first board using 

FA4652 wood screws.

5.  Recheck the frame assembly for sharp edges or 

clamps and bolts that may interfere with the installation 

of the curtain.  File or tape sharp edges as needed.

6.  Continue with the installation of the end frame and end 

panels. 

End Panel of Shelter

Curtain 

Panel

Ground Level

Baseboard and 

Retaining Board

Summary of Contents for Premium Moo-Tel CD


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands