background image

CLEARSPAN

 COLD FRAMES

14

Revision date: 12.29.08

FINISH ROUGH EDGES

Gather the parts:

Duct tape (supplied by customer)

• 

Metal file

• 

Check for any sharp edges on the frame and file them 

1. 

smooth so they will not cut the cover.
Apply two layers of heavy duct tape on all pipe  

2. 

connections and clamps that may contact the cover.

OPTIONAL COVER INSTALLATION 

(Cover is not included 

with standard cold frame.  Additional purchase is required if 

installing a cover and/or roll-up side accessory.)

 

 

The following sections describe the installation of a film 

cover. The cover shown in the following diagrams may 

differ from the actual cover. It is shown to illustrate a basic 

cover installation.

Additional parts and supplies must be purchased to 

complete the cover installation. 

These are not included with 

the basic cold frame components.

 

Contact Customer Service if you want to purchase a cover 

for your cold frame and to determine which cover and 

additional components are best suited for the application. 

OPTIONAL MAIN COVER INSTALLATION

After the frame is assembled and the baseboards are 

attached to the frame, the optional cover can be installed.

 

The steps to install the main cover include:

Install poly latch U-channel on the tops of the end 

1. 

rafters and to the baseboard.
Pull cover over the shelter.

2. 

Attach the main cover to one peak, stretch to the other 

3. 

peak and secure with poly latch spring.
Stretch the cover along one side and attach.

4. 

Stretch to other side and attach. 

5. 

Install Poly Latch U-Channel for Main Cover (No Roll-

Up Sides) 

 

NOTE: 

If you are installing a film cover and intend to 

have the optional roll-up sides for that film cover, skip this 

procedure and continue with the 

OPTIONAL MAIN COVER 

INSTALLATION WITH ROLL-UP SIDES

 procedure.

Using Tek screws, attach a section of the poly latch 

1. 

U-channel (#102179) to the top of the first end rafter. 

Begin at the 

top of the baseboard

 as shown below.

Continue to attach the U-channel sections working up 

2. 

and over the first end rafter. 

Tek screw

U-Channel

ATTENTION:

 The U-channel is attached to the top of 

the rafter and will bend with the curve of the rafter as it 

is attached. See diagram that follows.

Frame shown may differ slightly from actual frame.

End Rafters Only

Dashed line represents the U-channel. 

Summary of Contents for Gothic Style Cold Frame






























Reviews: