background image

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected] 

16

FieldShield YOURx-TAP

Installation Manual 

 _________________________________________________________

Manual 018446 REV A - AUG 2017

Standard Warranty

Clearfield warrants to the original purchaser of the Product sold hereunder is free from defects in material and workmanship under normal use and 

service, subject to exceptions stated herein. Product purchased is warranted as follows: Clearfield designed and branded Products are warranted for 

five (5) years: Products manufactured by Clearfield to customer prints and/or specifications are warranted for one (1) year; and any Product Clear-

field acquires from or through a third-party manufacturer or distributor and resells to Customer as the original customer will carry the manufacturer’s 

pass-through warranty, if any. In all cases, the warranty period commences on the date of shipment to the original purchaser.

Warranty Claim Procedure

If any Product purchased from Clearfield is found defective under the above warranty, the following basic procedure must be followed:

1.  Customer must contact Clearfield and obtain a Return Materials Authorization

2.  Following authorization, the Customer ships the product-freight collect-to Clearfield’s manufacturing facility

3.  Clearfield shall repair or replace the defective Product at its sole option and discretion, and return the repaired or replacement Product to Cus-

tomer’s site, freight prepaid

Note: If the Product is not found to be defective at Clearfield, the product will be returned to the Customer and the customer billed for freight in both 

directions.

Limitations of Warranty

Correction of defects by repair or replacement, at the option of Clearfield Inc, shall constitute the exclusive sole remedy for a breach of this limited 

warranty. Clearfield shall not be liable under any circumstances for any special, consequential, incidental, punitive, or exemplary damages arising 

out of or in any way connected with the product or with agreement to sell product to buyer, including, but not limited to damages for lost profits, loss 

of use, or for any damages or sums paid by buyer to third parties. The foregoing limitation of liability shall apply whether the claim is based upon 

principles of contract, warranty, negligence or other tort, breach of statutory duty, principles of indemnity or contribution, the failure of any limited or 

exclusive remedy to achieve its essential purpose, or otherwise.

Clearfield will not be responsible for any labor or materials costs associated with installation or incorporation of Clearfield products at customer sites, 

including any costs of alteration, replacement or defective product, or any field repairs.

Other Limitations

1.  Clearfield assumes no warranty liability regarding defects caused by:

2.  Customer’s modification of Product, excepting installation activities described in Clearfield documentation

3.  Customer re-packaging of Product for shipment to third parties or destinations other than those originally shipped to by Clearfield, or any de-

fects suffered during shipping where the Product has been re-packaged

4.  Customer’s installation or maintenance, excepting activities described in and performed in accordance with Clearfield documentation

5.  Customer’s improper or negligent use or application of Product

6.  Other causes external to the Product, including but not limited to accidents, catastrophe, acts of God, government action, war, riot, strikes, civil 

commotion, sovereign conduct, or the acts or conduct of any person or persons not party to or associated with Clearfield

Summary of Contents for FieldShield YOURx-TAP


















Reviews: