Clearfield FieldShield FLATdrop Installation Manual Download Page 3

Page: 3 / 22

FieldShield FLATdrop

__________________________________________________________

Installation Manual

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected]

Manual 018957 Rev C - July 2022

Application

Technical Specifications

Description

FLATdrop options designed to save contractors and installers time

and space in almost any deployment environment. The peelable outer

sheath of FieldShield FLATdrops allow for easy access to the inner

fiber elements (either 3mm or 900um) and each offer a large selection

of connector types in a pre-connectorized solution while allowing for up

to 100 feet of compact fiber slack storage. Clearfield’s suite of flat drop

solutions effectively meet the unique needs of your network deployment.

The FieldShield FLATdrop suite offers the first pre-connectorized flat

drop style cable to provide hardened environmental performance on a

peelable flat drop style cable without the added cost or dependency on

the market’s existing bulky connector. Connectivity to access terminals

is achieved through the innovative FlexConnector, which snaps into the

FlexPort, providing an air-tight and water-tight connection.

The FieldShield FLATdrop suite offers the first pre-connectorized flat drop style cable to provide hardened environmental

performance on a peelable flat drop style cable without the added cost or dependency on the market’s existing bulky con

nector. Connectivity to access terminals is achieved through the innovative FlexConnector, which snaps into the FlexPort,

providing an air-tight and water-tight connection.

Standard Flat Drop

FieldShield Peelable FLAT-

drop (With and Without

Rip Cords)

FieldShield Peelable Small

Form Factor FLATdrop

Coil Diameter

12”

8”

Slack Footprint of Sub-Unit

N/A

100ft

100+ ft

Sheath Jacket Dims

8.3mm x 4.7mm

5.4mm x 3mm

Sub-Unit

250μm

3mm

900μm

Connector Types

SC/APC, SC/UPC, HFOC

SC/APC, SC/UPC, HOFC,

Pushable

SC/APC, SC/UPC, HOFC,

Pushable

Deployment Environment

Aerial, Buried, Conduit

Summary of Contents for FieldShield FLATdrop























Search results

Summary of Contents for FieldShield FLATdrop

Reviews:

Related manuals for FieldShield FLATdrop

Brands by name

Popular brands

Clearfield FieldShield FLATdrop, Installation Manual

Search results

Summary of Contents for FieldShield FLATdrop

Reviews:

Related manuals for FieldShield FLATdrop

Brands by name

Popular brands