Clearfield FieldShield FLATdrop Installation Manual Download Page 20

Page: 20 / 22

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected]

FieldShield FLATdrop

Installation Manual

_________________________________________________________

Manual 018957 REV C - July 2022

Cleaning Using a Probe-Style Cleaning Tool

• The probe style cleaning tools are capable of cleaning a connector end face separately or through the adapter.

•

Slightly engage probe by pulling back but do not allow to click. Lightly “spot” a QbE-2 wipe on the platen with Elec

tro-Wash PX Fiber Optic Cleaner, this will help alleviate “over saturation” of the material.

• Lightly touch the tip of probe and release.

Wipe

Material

Wet

End

Face

Dry

•

Insert connector or insert probe though adapter and click 2-3 times to move past the wet area and allow material to dry

wipe.

•

Inspect connector, repeat if necessary (following standards)

•

If cleaning a male connector, clean the pins (see above)

Summary of Contents for FieldShield FLATdrop























Search results

Summary of Contents for FieldShield FLATdrop

Reviews:

Related manuals for FieldShield FLATdrop

Brands by name

Popular brands

Clearfield FieldShield FLATdrop, Installation Manual

Search results

Summary of Contents for FieldShield FLATdrop

Reviews:

Related manuals for FieldShield FLATdrop

Brands by name

Popular brands