background image

 

 

Page 10 of 10 

P/N G0200181 Rev A, 1.0.12.14.2015

 

 

ClearCube Technology, Inc. 

3700 W Parmer Lane 

Austin, TX 78727 

(512) 652-3500 

www.clearcube.com 

WEEE Disposal Guidelines

 

In the European Union, this electronic product falls under the European Directive (2002/96/EC) WEEE. When it reaches 
the end of its useful life or is no longer wanted, it should not be discarded with conventional waste, but disposed of at 
an approved designated recycling and/or treatment facility. Laws are different in each country, so please check with 
your local authorities for proper disposal instructions. For assistance, contact ClearCube a

[email protected]

.

 

Related Information and Support 

 

Related 
information 

The table below shows additional documents about server configuration, operation, and maintenance. 
 

For information about … 

See … 

Deployment guidelines for SmartVDI servers 

SmartVDI Converged Infrastructure Platform 
Deployment Guide 

NVIDIA GRID graphics card configuration 

GPU 

Quick Install Guide

 included with the 

SmartVDI server 

Installation services 

Contact ClearCube or your Authorized 
ClearCube Reseller. 

ClearCube documentation is located a

http://www.clearcube.com/support/

. 

 

Contacting 
Support 

Web 

UUU

www.clearcube.com/support/ 

Email 

UUU

[email protected]

 

Toll-free 

(866) 652-3400 

Direct 

(512) 652-3400 

 

 

Summary of Contents for SmartVDI-110











Reviews: