Clean Water Systems J-PRO-22 Installation & Start?Up Manual Download | Manualshive

Page: 7 / 16

background image

J-PRO-22 Alum Guide Rev 0021622 Page | 7

As an option to turn on and off the Alum pump, install a flow switch. No electrical wiring to do and any

plumber, or person familiar with basic plumbing, can install it.

Simply plumb the pre-wired flow switch into your service pipe. Plug the flow switch into a standard 120V

wall outlet.

Then, plug the Alum pump into the electrical outlet on the flow switch. Whenever there is flow, the

metering pump will then turn on.

J-PRO-22

Installation

Instructions

While you can mount

the pump on a shelf

above the solution

tank, it is strongly

advised to mount the

pump directly on top

«
...
5
6
7
8
9
...
»

Summary of Contents for J-PRO-22

















Reviews:

No comments

Related manuals for J-PRO-22

Brand: GC Water Pages: 15

Brand: PUR Pages: 30

Brand: Aquasana Pages: 9

Brand: Oase Pages: 102

Brand: AquaScape Pages: 20

Brand: JRC Pages: 4

Brand: Hans Pages: 65

Brand: Hydro International Pages: 17

Brand: Conergy Pages: 36

Brand: BROTJE Pages: 76

Brand: Scottoiler Pages: 1

Brand: Viesta Pages: 12

Brand: Komet Pages: 23

Brand: IDEAL H2O Pages: 7

Brand: Innowater Pages: 12

Brand: Innowater Pages: 18

Brand: Innowater Pages: 32

Bottle Movement

Brand: LARQ Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands