background image

 

 

 

 

 

Clean

 

Water

 

Made

 

Easy

 

www.cleanwaterstore.com

 

                                     

 

7500

 

Greensand

 

Filter

 

Installation

 

&

 

Start

Up

 

Guide

 

Thank

 

you

 

for

 

purchasing

 

a

 

Clean

 

Water

 

System!

   

With

 

proper

 

installation

 

and

 

a

 

little

 

routine

 

maintenance

 

your

 

system

 

will

 

be

 

providing

 

iron

 

free

 

water

 

for

 

many

 

years.

 

Please

 

review

 

this

 

start

up

 

guide

 

entirely

 

before

 

beginning

 

to

 

install

 

your

 

system,

 

and

 

follow

 

the

 

steps

 

outlined

 

for

 

best

 

results.

                                          

 

  

 

GREENSAND

 

MEDIA

 

CONTAINS

 

DUST.

  

USE

 

PAPER

 

MASK

 

AND

 

VENTILATE

 

TO

 

AVOID

 

BREATHING

 

DUST.

 

 

 

 

 

 

 

 

 

 

Questions?

 

Call

 

us

 

toll

free:

  

1

888

600

5426

 

or

 

1

831

462

8500

 

Email

 

us:

  

[email protected]

 

See

 

more

 

information

 

on

 

our

 

website:

  

www.cleanwaterstore.com/resources

 

Summary of Contents for Greensand 7500














Reviews: